Recommendations for a good Rotary Buffer

Makita 9227CX3 7" Right Angle Polisher / Light Sander



$179.00





Standard Equipment

Hex Wrench

Hook & Loop Pad



Accessories

Polisher Accessories



7" Abrasive Discs: 7/8" Arbor Hole Included for a

Limited Time!

Polisher Accessories

Includes 21" tool bag, 7" compound pad, and a 7" polishing pad. A $50 value!



Specifications

Amperage: 10.0

No-load RPM: 0 - 3,000

Sanding Disc: 7" (180mm)

Spindle Thread: 5/8" - 11 UNC

Length: 181/2" (470mm)

Weight: 6.6 lbs (3.0 kg)



Features

Variable speed with pre-set maximum speed dial – ideal for ultra slow polishing.

Electronic speed control maintains constant speed under load.

Easily converts to a sander.

Fast and powerful polishing for clear-coat finishes.

Lock-0n button for continuous use at one speed.



Is this rotary okay? Looks perfect for minor detailing corrections that PC is just not adequate.
 
That's what I bought....based on the recommendatin of my friend who owns a body shop and has used his Makita for over 10 years with no break downs and perfect performance.
 
blkZ28Conv- Heh heh, so you're gonna step up to a rotary too, huh? I think you'll like it...there are times when it's just the right thing.



Give a little thought to how YOU will use it. I ended up going with the Makita 9227CY with the 90 degree side handle (like that on the PC) instead of the "hoop" handle. It was a more natural progression for *ME* compared to getting the hang of something totally different. I end up taking the handle OFF a lot of the time, just like with the PC (which virtually NEVER has its handle on).
 
Accumulator said:
blkZ28Conv- Heh heh, so you're gonna step up to a rotary too, huh? I think you'll like it...there are times when it's just the right thing.



Give a little thought to how YOU will use it. I ended up going with the Makita 9227CY with the 90 degree side handle (like that on the PC) instead of the "hoop" handle. It was a more natural progression for *ME* compared to getting the hang of something totally different. I end up taking the handle OFF a lot of the time, just like with the PC (which virtually NEVER has its handle on).
Click to expand...



Yes, I think I need to graduate up to rotary for some blemishes ( etching) that the PC just can not handle. They are far less evident now after PC'ing SEVERAL times but under certain light angles they are quite evident to me.

Fortunately, these blemishes are only on the hood. Plus it is time to advance my skills and increase my detailing ability :xyxthumbs



Now I just have to figure out the pad / backing plate situation so that I can order everything at one time. :wavey
 
blkZ28Conv said:
Now I just have to figure out the pad / backing plate situation so that I can order everything at one time. :wavey
Click to expand...



I got the larger ("regular" for a rotary) plate with mine, but I prefer using 6.5" pads, so I got the appropriate flex plate from CMA. I also got the small one (maybe 3" ?) which I use with my Cyclo pads for localized repairs.



I think you'll find the pad selection/application goes about the same as with the PC, only with fewer applications for a finishing pad. Plus you can do a lot more with polishing pads so there's a LITTLE less use of cutting ones (depending on your product choices). The pad interchangeability is another reason I like using 6.5" pads with both the rotary and the PC. *VERY* handy.
 
Accumulator,

I can get a 6" backing plate from CMA to fit the Makita 9227CY and use the same 6.5 inch pads I justed purchased from Meguiar's for my PC? That would be GREAT. I feel I would have better control with the 6.5" pads.

TIA
 
I just bought the Metabo yesterday it should be here by the end of the week. It's a little more money than the others, but I like the fact that it is around the same size and weight as the PC, but only a rotary.
 
I was in the same situation and went with the DeWalt. I have no problems with it at all. Its got a real heavy, but balanced feel. Its old school baby. I was scared at first, but the lowest speed setting is pretty slow and allows you to work up to faster speed. I got the flexible urethane backing plate 6 1/8" from CMA and then 7 1/2 in pads from TOL. I couldn't be happier.



Also- got the DeWalt from Harbor Freight- took about 8 days to get to my house.
 
jessispop said:
I just bought the Metabo yesterday it should be here by the end of the week. It's a little more money than the others, but I like the fact that it is around the same size and weight as the PC, but only a rotary.
Click to expand...



Thats the one I have for a year now, does what the 'big boys' do but doesn't weight as much. It's only inconvenient would be if you're buffing cars all day, it might not old as well a DeWalt...



I think it would be the right one for you Edwin :xyxthumbs
 
blkZ28Conv- Yah, just make sure you order the 6" (maybe it's 6.125" like Greg said) flex plate for the ROTARY, not the 5" one for the PC ;) BTW, Meg's pads often last a lot longer on a rotary than they do on the PC. They were made for the rotary and the PC's "jiggle action" is sorta tough on them by comparison.



Greg- Yeah, I ALMOST went with the Dewalt. It reminded me of the Milwaukee I used back in the day. That IS a nice unit.



But no one needs to worry about the Makita holding up; I know guys who've used them every day for years with no problems.



jgv- Where's the on/off switch located on that Metabo? Is it on top like the PC? Sorta looks like it in your pic.
 
Hey JGV, can you elaborate a little more on the Metabo? It looks like great little machine given the rotary capabilities bottled in the PC size and weight.



I don't mean to hijack the thread, but I think if it's good enough, it should be factored into the Dewalt / Makita debate.



Better yet, tell me why I shouldn't add it to the PC / Makita arsenal I have!



The cheapest I saw was $259 based on a quick Google search.
 
The On/Off switch is locate on top, like on the PC. It weighs less than the PC and has variable speed (visible).



It works very well, specially with 6" pads, and is very easy to work with, even in lower sections.

You can feel the benefits of being light weight after a few hours of buffing. ;)



TOL sells them also.
 
Thanks again Guys. Great response and information. I am really only going to use the rotary for spot corrections (well that what I intend to do :o). I ordered the el-cheapo from CMA to see if it will do the job. Normally I would just spend a few more $$ for the tried and proven model but because of the limited use I am going on CMA's rating of this Vector machine. I am sure if this item appears unable to do the minor jobs I require that I can sell it for ~$30 and with the free shipping offer at CMA only loss a few $$.

Wish me luck. I am going by a Body Shop today a try to pick up a practice panel, then the daily driver silver metallic and finally the black babies. :bounce



Accumulator: Cool the Meg pads are perfect!! :bow . They will arrive on Monday the 22nd.
 
Just curious: does anyone use this polisher?



Model 7428





And - oddly, when I go onto Lowe's web site, they don't list the PC Random Orbit anymore. Do they still carry it? I know that's where my wife bought mine for Christmas.
 
jgv- Thanks for elaborating. The switch location would be a deal-breaker for *ME*, as I don't like a slide-switch in that location (the one on the PC really bugs me) and I like the gradual ramp-up/down of a trigger. But as that's just a personal preference thing, people who LIKE the PC oughta keep the Metabo in mind.



blkZ28Conv- Be careful using that Vector. NOT wanting to get into a flame war with Vector-fans, I still want to point out that it does NOT (*as I understand it, no first-hand experience*) maintain a constant speed under load. I hear it slows down under load and that wouldn't work for *ME* as I want to have as much control over a rotary as I possibly can. A few hunderd rpms can make a BIG difference. I REALLY don't mean to rain on the parade here, but be sure you really LIKE it during your return-privilege timeframe. I figure that even though my Makita doesn't get much use, the price difference was pretty insignificant compared to having to pay a more experienced operator (or a paint shop!) to fix something.



Gee I sound negative/contrary :o
 
You must log in or register to reply here.
Back
Top