Should I wax my Clearbra?
- Thread starter jw
- Start date
imported_DJ Mayo
New member
you make alot of threads. Search.
Yes, you can use any non abrasive wax or sealant of choice on the clear-bra, but be careful not to cake any product in the edges or it will be very difficult to get out and look horrible.
Plexus, Opti Seal, Clear Seal, OCW or UPGP would be a better choice since they will not leave any residue behind...
Plexus, Opti Seal, Clear Seal, OCW or UPGP would be a better choice since they will not leave any residue behind...
EBPcivicsi
GOT PREP?
We use a lot of OCW or Z8 on the film that we install--M135 is great as well.....
blk45
It's all in the prep!
RickRack said:
Agreed....
It's obviously been proven that other stuff works well, but every installer that I know recommends only using Plexus for clear bras.
imported_RZJZA80
New member
I used KAIO on a black Porsche with a clear bra and it worked great
Accumulator
Well-known member
jw- I'd wax it too. But...
-To avoid build-up along the edges, move the applicator from well inside the clear bra straight towards/off the edge (if that isn't clear say so and I'll restate it). Then go back inside the clear bra's area and do the next swipe again back towards and off the edge. Repeat the application this way, always going from within the clear bra-ed area towards/off the edge. That'll minimize the wax build-up but you'll probably get a little anyhow.
Try buffing it off the same way but also try moving the buffing medium along/parallel to the edge of the clear bra.
-Some waxes sorta "sweat" when applied to PPFs. This'll be most noticeable a while after the wax has been buffed off. If/when this happens, I'd spritz the area with a little QD before buffing off the "sweat" least you mar the clear film. I've had this happen in odd ways; one area would have it and another wouldn't :nixweiss Just wanted to mention it so you don't
if it happens to you. I *think* it has to do with the way waxes sorta sit on surfaces as opposed to bonding in the way that sealants do but I dunno for sure.
-To avoid build-up along the edges, move the applicator from well inside the clear bra straight towards/off the edge (if that isn't clear say so and I'll restate it). Then go back inside the clear bra's area and do the next swipe again back towards and off the edge. Repeat the application this way, always going from within the clear bra-ed area towards/off the edge. That'll minimize the wax build-up but you'll probably get a little anyhow.
Try buffing it off the same way but also try moving the buffing medium along/parallel to the edge of the clear bra.
-Some waxes sorta "sweat" when applied to PPFs. This'll be most noticeable a while after the wax has been buffed off. If/when this happens, I'd spritz the area with a little QD before buffing off the "sweat" least you mar the clear film. I've had this happen in odd ways; one area would have it and another wouldn't :nixweiss Just wanted to mention it so you don't
if it happens to you. I *think* it has to do with the way waxes sorta sit on surfaces as opposed to bonding in the way that sealants do but I dunno for sure.
blk45
It's all in the prep!
It's obviously been proven that other stuff works well, but every installer that I know recommends Plexus only for clear bras.
imported_DetailDan
New member
Ive read some waxes may cause the clear bra to yellow, headlights also. Use something without dyes and that actually has UV protection.
HTP AutoWorks
New member
Use a good wax or sealant on the clear bra. Your installer should have told you this when you got it installed. I recommend to all my clients to maintain the film just as you would your paint. It needs a good wax or sealant on it to keep it looking good. I always recommend Zaino...