512detail
New member
not really a review...
requires a little info...
the drivers door and fender were the subject of some tlc tonight
allow me to show you a short video clip I took last week when I was coating my trunk and drivers side rear quarter panel with csl+exo
not bad, yes, but I kept thinking I did that on the worst looking panel on my car (driver side door) which just has black hole and Wulfenite on it (terrible, I know-hah)
the door closer
pretty swirled actually but i did a crappy job of showing it..either way you can take my word for it. it was non autopian for sure. i didn`t even plan to make this thread but turns out I had two hours to kill
anyways, i had to use a heavy cutting compound (p1) via duetto and mf cut disc to get it where i wanted it
you can see the line on the right and the lack of gloss present relative to the left side which was unpolished but got a dose of iron removal and claying yesterday and sat in garage since then
then i looked at this
next I taped off a section and wanted to see if invincible primer would give me the gloss back
the bottle says can be used as compound or polish depending on pad selection, so I figured I`d give it a go on the rupes yellow pad which I know would have worked just fine with some other polishes but I was hoping for invincible primer asy 2nd step product, not third...
first thing I noticed is the thick consistency and a little goes a long way
oh yea,it also smells fantastic!
and it definitely works just fine on the yellow pad after a cutting micro pass with heavy compound
see...
completed the rest
now for some cosmic v2 applied via duetto and carpro gloss pad
probably applied too thick but I didn`t even use much, but probably too much so i let it sit 40 mins
first layer flashed and removed
now only 20 more minutes until i can apply the 2nd layer and wait another hour to apply cosmic, lol
im getting lots of random things done in the house while I wait
can`t wait to see the shine once its cured
took this right after I removed the first layer
edit:finally got 2nd layer on and cosmic spritz applied..there is a lot of waiting if you don`t do the entire vehicle at once
should be cured by the time I get home from work tomorrow. rest of car needs a rinse and gloss enhancer spray for a car meet Saturday
requires a little info...
the drivers door and fender were the subject of some tlc tonight
allow me to show you a short video clip I took last week when I was coating my trunk and drivers side rear quarter panel with csl+exo
not bad, yes, but I kept thinking I did that on the worst looking panel on my car (driver side door) which just has black hole and Wulfenite on it (terrible, I know-hah)
the door closer
pretty swirled actually but i did a crappy job of showing it..either way you can take my word for it. it was non autopian for sure. i didn`t even plan to make this thread but turns out I had two hours to kill
anyways, i had to use a heavy cutting compound (p1) via duetto and mf cut disc to get it where i wanted it
you can see the line on the right and the lack of gloss present relative to the left side which was unpolished but got a dose of iron removal and claying yesterday and sat in garage since then
then i looked at this
next I taped off a section and wanted to see if invincible primer would give me the gloss back
the bottle says can be used as compound or polish depending on pad selection, so I figured I`d give it a go on the rupes yellow pad which I know would have worked just fine with some other polishes but I was hoping for invincible primer asy 2nd step product, not third...
first thing I noticed is the thick consistency and a little goes a long way
oh yea,it also smells fantastic!
and it definitely works just fine on the yellow pad after a cutting micro pass with heavy compound
see...
completed the rest
now for some cosmic v2 applied via duetto and carpro gloss pad
probably applied too thick but I didn`t even use much, but probably too much so i let it sit 40 mins
first layer flashed and removed
now only 20 more minutes until i can apply the 2nd layer and wait another hour to apply cosmic, lol
im getting lots of random things done in the house while I wait
can`t wait to see the shine once its cured
took this right after I removed the first layer
edit:finally got 2nd layer on and cosmic spritz applied..there is a lot of waiting if you don`t do the entire vehicle at once
should be cured by the time I get home from work tomorrow. rest of car needs a rinse and gloss enhancer spray for a car meet Saturday
