McKee`s 37 Hydro Blue Sio2 Coating

[Metalvolvo]

So today I used the Hydro Blue and it was easy and the gloss is amazing.. one thing I didn`t like was when I was drying it, it kept leaving an oily film. I had to rewash the car and nothing... So I just ended up using ONR over it and it helped a little.. does anyone know what happened?

[PA DETAILER]

That`s a first. You did hit it with a strong stream of water when rinsing correct? Panel at a time. Used it several times. Never had this happen. Was the vehicle stripped of prior product before hydro blue? I used a iron remover before application.

[Metalvolvo]

That`s a first. You did hit it with a strong stream of water when rinsing correct? Panel at a time. Used it several times. Never had this happen. Was the vehicle stripped of prior product before hydro blue? I used a iron remover before application.

Yes I did. Pressure washer.. I did one pass.. maybe I should kept it longer. Just clayed only..

[Ronkh]

Please give complete process....

Something not right.

[Metalvolvo]

Washed with Nanoskin Cherry.. clayed with CG yellow clay bar. Rinsed off again, while still wet went and applied hydro using a kwazar sprayer in sweeping motions (might of put to much?) Rinsed again with pressure washer.. started to dry it and noticed the oily marks.. and wouldn`t buff off.. so I rewashed it and it got better but still there. Brought out ONR to help take it off

[Metalvolvo]

Please give complete process....

Something not right.

Washed with Nanoskin Cherry.. clayed with CG yellow clay bar. Rinsed off again, while still wet went and applied hydro using a kwazar sprayer in sweeping motions (might of put to much?) Rinsed again with pressure washer.. started to dry it and noticed the oily marks.. and wouldn`t buff off.. so I rewashed it and it got better but still there. Brought out ONR to help take it off

[dcjredline]

Ive not used the McKees but if you put that much HydrO2 on you would have definitely over applied. They recommend 1 to 2 spritzes per panel. WOW a kwazar?

EDIT: Not being a smart ass...do they have instructions on the bottles?

[Ronkh]

Washed with Nanoskin Cherry.. clayed with CG yellow clay bar. Rinsed off again, while still wet went and applied hydro using a kwazar sprayer in sweeping motions (might of put to much?) Rinsed again with pressure washer.. started to dry it and noticed the oily marks.. and wouldn`t buff off.. so I rewashed it and it got better but still there. Brought out ONR to help take it off

What did you use for clay lube? Was it washed off ?

[Metalvolvo]

Yeah I know, I think I over applied

[Metalvolvo]

Nanoskin glide.... Didn`t wash it, just rinsed.. maybe this?

[Ronkh]

Nanoskin glide.... Didn`t wash it, just rinsed.. maybe this?

I`d bet on it.

[Tpr1634]

I found the out the hard way do not apply in direct sun it will leave stains I figure it dries to quick.

[Oneheadlite]

Nanoskin glide.... Didn`t wash it, just rinsed.. maybe this?

I`d bet on it.

I’m with Ronkh. I would bet the slippery stuff from any clay lube would need to be physically washed off, not just rinsed off.

[Dan]

I’m with Ronkh. I would bet the slippery stuff from any clay lube would need to be physically washed off, not just rinsed off.

I just re-leared that lesson a few months ago when I had some FK1000P fail in about two weeks because I didn`t wash/polish after claying.

[nickclark08]

Speaking from my experience with the stuff, It will streak if used on too hot a surface, used too much, or didn`t wash off clay lube / etc..

Applying this stuff in a kwazar is not needed - way too much product. two or three sprays per panel tops, then immediately rinse off.