Tape it off and avoid a lifetime of ugly...

[Mike Phillips]

Tape it off and avoid a lifetime of ugly...


So many times in my life when I`ve buffed out a classic car, when I first get to the car and inspect it I find compound and polish residue splattered into impossible to reach areas.

A good example of this is the fresh air intake grill usually right before the front of the windshield.

Here`s an example, the 1969 El Camino I used for this article on Dampsanding, Damp-Sanding Tools, Tips and Techniques


Upon inspecting the paint I found the typical ugly compound and polish residue splattered inside the fresh air grill left by the guy that buffed the paint out before me.

Here`s the 1969 El Camino...



Here`s the ugly part...



Because the bottom side of the sheet metal where the slots are stamped out are rough and jagged, all the compound and polish residue that was splattered by the rotary buffer has embedded like cement and will be very difficult to fully remove, especially now that it`s a few years old...


Close-up...




So while this is a very beautiful 1969 El Camino, every time someone looks at the hood area from the side of the car their eyes will be drawn to the very apparent white compound and polish residue that is encrusted where it`s hard to reach and remove.


The first thing I did upon finding the compound splatter inside the grill was to point it out to the owner so he would know that I didn`t create the problem and then while he was standing there, I took photos of the crusty splatter so that it was established that the splatter was there before I ever worked on the car.

This is a good best practice for your own detailing business because you don`t want to get blamed for The Other Guy`s Wax or TOGW

TOGW = The Other Guy`s Wax


So here`s a tip...
Before machine polishing any vehicle with areas that will be hard and even impossible to detail later should any compound or polish residue be splattered into these areas is to take a few moments to tape, cover and protect these areas from splatter before starting.

For example, here at Autogeek`s Show Car Garage we are regularly asked to test out upcoming products for many of the manufactures we represent and then file a report with our results and observations. Yesterday I had 4 different products from 3 different manufactures to test that involved machine sanding and using a rotary buffer.

My test vehicle was our in-house 1964 Ford Falcon which has extreme orange peel, so it offers plenty of real-estate for testing a variety of different products.

As far as I can tell this car has never been machine polished, either before it was repainted nor after it was repainted because there are no signs whatsoever of splatter underneath the fresh air intake grill.

I`m not going to be the first person to get splatter into this area so before starting the testing I simply taped the grill off using Meguiar`s Professional Masking Tape, which is a brand new masking tape made especially for use on automotive paints.

Taping off areas like this takes just a little time in the beginning of a detailing project as compared to the massive amount of time it will take to try to remove any splatter after the project is finished. And in some cases, it`s all but impossible to remove splatter residue in hard to reach areas, so taping off and covering up ensures no splatter and protects your customer`s car`s appearance and your reputation.

Zero splatter under the grill of this 1964 Ford Falcon







Meguiar`s Professional Masking Tape



After the sanding and buffing, remove the tape and no spatter... no ugly... no worries...

[Dans Detailing]

Love the shine! Classic cars are so very fun to do!!

[Dr Oldz]

Masking tape is your friend!

[WelshDog]

What am I missing here? If you mask that area how do you then get it polished and waxed?

[Mike Phillips]

What am I missing here? If you mask that area how do you then get it polished and waxed?

Carefully by hand after you`re finished with any machine steps.

You could also work the areas you`re going to cover up first and then tape or cover them up, but most people would tackle them after the machine steps.


You could skip it if you like, personal preference.


One thing for sure, I`m not going to be the guy that gets compound, polish or wax residue into areas I cannot remove it and have the owner upset with the quality of my work, especially something "Special Interest".

[WelshDog]

Carefully by hand after you`re finished with any machine steps.

You could also work the areas you`re going to cover up first and then tape or cover them up, but most people would tackle them after the machine steps.

Got it, makes sense. I learned something today while I was masking. We mask to keep product off of the black trim and plastics, but we also mask (as you showed us here) to keep residue out of the crevices. I found if I carefully placed the tape over the black plastic trim and also lapping over a small line of paint you keeps stuff out of those hard to clean valleys. Sure you end up with a tiny strip of untreated paint, but like you said one can go back over this by hand if need be.

I was wondering about door, hood, trunk and hatch gaps. Since you can open these things it seems covering those gaps is not necessary. It`s easy to get at these edges after the fact and clean them. True?

[Mike Phillips]

I was wondering about door, hood, trunk and hatch gaps. Since you can open these things it seems covering those gaps is not necessary. It`s easy to get at these edges after the fact and clean them. True?

Sure!

I know a lot of guys that do just that, open a door, hood, trunk lid etc. buff up to the edge then wipe any residue off. While the door, hood or trunk lid is open, buff the adjacent panel and wipe the residue off...