Rotary Usage

**cheapshot** · 11-04-2007, 08:04 AM

I did it, I bought a dewalt 849. I tried a small section on the hood of my sisters car! I used edge blue light cutting and ssr2.5 at 1000/1300rpm, I have lots of practicing to do. The polisher did a lil dace a few times on me, I think this was do to a bit of dry buffing. So I tried the section again, still I was left with some haze. All the swirls were removed with the exception of a few deep scratches. So I took out the pc edge polishing pad and ssr1, worked it well two applications. All the swirls were gone, and all the hazing was gone.

I love to use SSR2.5 with my PC, But I might need to start look at some products that work a little longer for dewalt.

Any suggestion?

PS: i would of tried #80 or #83 but, i took them out and they were all caked up in the bottle? #80 was caked and turned a lil green and #83 i shook till dealth, would not mix?

**cheapshot** · 11-13-2007, 06:35 AM

I remember seeing a thread on rotary use, were they describe left to right, right to left, and say to pay attention to the section between 12 + 3 o`clock position, or something to this nature.

I ask this because the buffer tried to get away a few times pulling in a direction I was not aiming for. should the pad really be 100% flat? or at least at all times?

how do you control it better using trialling edge, leading edge etc.

**nyne11** · 12-05-2007, 04:48 AM

I have just purchased a rotary to add to my detailing inventory and after reading this entire thread I am now eager to try it out I will try it out on the wife`s Hyundai first and gradually work up to my pride and Joy! Thanks to all who have contributed to this thread as it is a wealth of knowledge and without the good people out there who are willing to take the time to share their experiences and expertise with the rest of us there would be far less enthusiasts!:goodjob

**Fly Bye** · 12-05-2007, 05:04 AM

Originally Posted by BradE

Absorb this information grasshopper, more to come.

**SVR** · 12-20-2007, 10:38 PM

In my eyes, pads should always be 100% flat on the surface at all times

Not doing so causes swirls

**ICANDY** · 12-24-2007, 12:46 AM

Originally Posted by SVR

In my eyes, pads should always be 100% flat on the surface at all times

I agreee but

Originally Posted by SVR

Not doing so causes swirls

Not True.

d.

**SVR** · 12-24-2007, 03:13 AM

Then what causes the swirls that body shop detailers put in. Dry pad thats clogged with polish?

**ICANDY** · 12-24-2007, 04:22 AM

Not sure, it could be a number of issues most likely it`s related to either incorrect compound or pad usage. Swirls could be marring from an aggresive compound that they haven`t polished out.

I use the edge of my pads from time to time even though I agree with the flat pad rule you stated earlier. I even used a wool (acrylic) pad on this panel and used the edge to speed up cutting in certain areas.

closeup:

Risky I know and not technically perfect but I have a little experience and know what I am doing. I did leave behind hideous marring but corrected the swirling and holograming behind and acheived this finish after an alcohol wipe (no lsp):

closeup:

**imported_Moutee** · 01-09-2008, 11:31 PM

I saw someone above mention a concern of mine, and that is holding the pad at a slight angle versus 100 percent flat. I`m inexperienced, probably the number one reason why, but when I try to hold the machine flat, it wants to go in it`s own direction.

Also, is it necessary to give a pad a spray with QD before buffing, and what is the proper way (direction) to move along vertical panels?

Thank you.

**ICANDY** · 01-10-2008, 12:08 AM

Use a smaller pad. There is obviously too much grip on the pad. I use a 6" versus the notmal 8" when I experience that problem.

It may or may nto work for you but it`s definately worth a shot, reducing friction via this method seems to work for me.

d.

**SVR** · 01-10-2008, 12:36 AM

You missed the wiper arms damian.

A little aussie gold would give that panel some extra bling.

**ICANDY** · 01-10-2008, 12:45 AM

I don`t polish wiper arms mate

haha, are you serious? I hate that Aussie Gold stuff

**SVR** · 01-10-2008, 03:29 AM

Haha, your missing out

I`m referring to Showroom Glaze. There ain`t no other QD that can match it or last as long

Well that`s one thing that I have over you, I love doing wiper arms with my trim dream.

I personally believe that they make a big difference to the overall look.

When I order products, Barry makes them up according to my specifications. If I want a longer working time, different colour or an ingredient removed, he does it.

I give him my feedback on any products and he makes changes.

Aussie Gold Clear Cut (my version)

**ICANDY** · 01-10-2008, 04:18 AM

ah huh, I understand now why you pushing this Aussie Gold stuff so hard

I don`t like glazes Matt, no clarity.

I`ll stick to this high clarity carnauba instead:

**imported_Moutee** · 01-10-2008, 08:39 AM

Originally Posted by ICANDY

Use a smaller pad. There is obviously too much grip on the pad. I use a 6" versus the notmal 8" when I experience that problem.

It may or may nto work for you but it`s definately worth a shot, reducing friction via this method seems to work for me.

d.

The pads I use are 6".