I use sponge pads instead of wool thats what i think helps out alot
I use sponge pads instead of wool thats what i think helps out alot
Michael`s Detailing
Does anyone tape edges off, for example where two doors meet or where a door meets a fender?
2010 Nissan 370Z
Superior Auto Care
Originally Posted by DSVWGLI
I pretty much tape off the whole car. Anywhere where there is rubber and paint meeting itgets taped. If it needs alot of buffing, say with a foam cutting pad, wool pad, etc. I will tape of edges as well.
The brown paper that painters use is a great help when masking large areas...saves on tape.
Anthony
"The Art & Science of Auto Detail"
Thanks Anthony, what speed do you polish edges at and do you lift the edge of the pad that cuts into the edge of the panel?
2010 Nissan 370Z
Superior Auto Care
Originally Posted by DSVWGLI
I feather the trigger when I get close to the edges. I buff into an edge while triggering the buffer.
Anthony
"The Art & Science of Auto Detail"
I read a handfull of post in this thread and have absorbed a bunch, thank you to all that have contributed. However.. after 7 pages my eyes hurt so I skipped to the last page.
Ive heard the term "pass" used a few times in various threads. When using my PC7424 I use the word "pass" when I refer to completeing a whole section. IE.. "I made a pass with the PC and #80 on a 1/4 size section of the cars hood." or " I did one pass with the #80 and PC to the whole car, I may need to make another pass to the whole car to remove more issues."
I want to make sure the term pass is used with the rotary in the same fashion. I get the feeling that when the word "pass" is used, when speaking of a rotary, it means gliding over a certain section 1 time. For instance "I made one pass on the 2x2 section @ 600rpm to spread, then made 2 passes @ 1200 on the same section."
Do you see what I mean? With the PC a "pass" on a 2x2 section means..... spending 3-5 minutes on that particular 2x2 section, which means I would glide the PC over each square inch MANY times. With a rotary a "pass" means I went over every square inch of that particular 2x2 section ONE time.
Am I correct? Im sorry if that makes no sense... its late.
-2002 35th Anniversary SS Camaro Limited Edition-
-651rwhp/567rwtq @ 6400rpm.
-D1SC Procharger-Custom Cam-FMIC-6.0L Heads-9psi-
35th, to me a `pass` is working over a particular section until the product has broken down, as you suggest a `pc pass` is, regardless of machine used. I agree everyone should use the same terminology and mean the same thing for consistency of conversations..
i have a 7 in rotary with a solid back plate should i get a flexabile one.
Originally Posted by craigjshcr
I would as it gives you smoother operation, IMHO.
Anthony
"The Art & Science of Auto Detail"
Question about taping, do you guys tape the around the gas cap cover. If so, how do end up polishing it, and other tight spots/narrow areas?
Originally Posted by noooorb
Personally I don`t tape that area. For small tight areas I either do it by hand or use a 3inch backing plate and 3 or 4 inch pad.
Anthony
"The Art & Science of Auto Detail"
By rotary...You can find these at some body shops
"The Art & Science of Auto Detail"
I`m too lazy to read this whole thread, just wondering what causes the pad to jump/skip... happens to me sometimes and 99% of that sometimes it`s on vertical surfaces... too much product??
Originally Posted by lecchilo
Could be that you`re over extending your reach so try bringing it in, use a step stool to gain some height and also buff with the pad at a slight angle.
Anthony
"The Art & Science of Auto Detail"
There are currently 1 users browsing this thread. (0 members and 1 guests)
Bookmarks