Results 1 to 11 of 11
  1. #1
    William_Wallace's Avatar
    Join Date
    Jun 2017
    Posts
    737
    Post Thanks / Like

    DIY mechanic tool needed

    I do my own work…sometimes if it’s not winter. Just did inner, outer tie rod, struts, rear shocks, caliper, rotors, brakes, stabilizer, new Lca with ball joint already pressed in.

    But got stopped dead in my track by wheel bearings already bought one tool that didn’t work, tried a lot of heat, air hammer and sledge and slide hammer. Wheel bearing laughed at those attempts.

    Recommend me a tool something beefy is ok. Budget is $300. I was going to go to harbor freight that a frame/body straighting kit works by hand pump hydraulic and it has a10 ton short throw ram that is small enough to sneak between the knuckle and hub May work that was suggested to me thing looks like like giant grease gun that has hose with looks of attachments to push or pull heavy objects small distances

    On hand I have 30 gal compressor and air Cromwell impact tried reversing wheel stud trick with bolt and nuts that did fail to

  2. #2

    Join Date
    Apr 2011
    Location
    New Jersey
    Posts
    12,545
    Post Thanks / Like

    Re: DIY mechanic tool needed

    What kind of vehicle?

  3. #3
    SUPER MODERATOR GearHead_1's Avatar
    Join Date
    Jul 2003
    Location
    Utah
    Posts
    10,625
    Post Thanks / Like

    Re: DIY mechanic tool needed

    Well, depending upon the type of vehicle, in most cases I`d say pull the steering knuckle off and find someone to press it out. That said, are you sure there is no circlip in the knuckle securing the bearing?
    A society willing to trade liberty for temporary security deserves neither and will lose both
    ΜΟΛΩΝ ΛΑΒΕ
    Likes William_Wallace liked this post

  4. #4
    SUPER MODERATOR GearHead_1's Avatar
    Join Date
    Jul 2003
    Location
    Utah
    Posts
    10,625
    Post Thanks / Like

    Re: DIY mechanic tool needed

    Then again, if you`re bound on spending $300, you can buy a 20-ton press that you can use for light-duty stuff that would be an addition to any shop.
    A society willing to trade liberty for temporary security deserves neither and will lose both
    ΜΟΛΩΝ ΛΑΒΕ
    Likes William_Wallace liked this post

  5. #5
    William_Wallace's Avatar
    Join Date
    Jun 2017
    Posts
    737
    Post Thanks / Like

    Re: DIY mechanic tool needed

    It would be use on multi vehicle Ford Edge SUV’s and f150 trucks thanks for the help. On the edge front cv axels rusted into. Some just mentioned just buy pre assembled new knuckles and just worry about separating the cv and knuckle and a lot of heat and air hammer should work

    I’m still open to specific hub tools.

  6. #6
    William_Wallace's Avatar
    Join Date
    Jun 2017
    Posts
    737
    Post Thanks / Like

    Re: DIY mechanic tool needed

    Quote Originally Posted by GearHead_1 View Post
    Then again, if you`re bound on spending $300, you can buy a 20-ton press that you can use for light-duty stuff that would be an addition to any shop.
    Lol yea I can make some room for a nice press

  7. #7
    Oneheadlite's Avatar
    Join Date
    Sep 2016
    Location
    Andover, MN
    Posts
    657
    Post Thanks / Like

    Re: DIY mechanic tool needed

    Just to clarify - you`ve gotten the CV out of the hub and are trying to pull the hub from the bearing, yes?

    Not familiar with the cars you`re working on, but I`ve done a great many wheel bearings.

    If the axle is out of the way:
    My preferred method is to use a bridge setup that presses against the bearing housing to pull the hub out of the bearing. Sometimes bearing housing shape doesn`t allow (don`t have sufficient area to press against - side note: Never press on brake caliper mounting ears! Seen a lot of guys do a lot of damage trying to do press work...) ; in those cases we just do the good old fashioned slide hammer approach. Most slide hammer kits you buy have really light duty slides (3lbs) - if you can, find something heavy to add (old brake rotor/etc) to increase your impact to help pop it out.

    Google: Hub Grappler - in that image you`ll see the bridge setup I`m referring to. That`s the kit we use at our shop. In the DIY realm, I`d call around and see what your local parts stores rent out and look at "renting" a wheel bearing tool. Usually you "purchase" the tool, then they give you your money back when you return it.

    If the axle is refusing to come out of the hub, let me know and I can try to explain what I`ve done for that. Short version: Snap on has a forcing screw you use in the slide hammer adapter you bolt to the hub. Apply force with that, then shock the axle with strikes on the end of the forcing screw with a brass hammer. Also, penetrating oil and time are your friends...

    Let me know what step you`re at and I`d love to help.
    Likes William_Wallace liked this post
    Thanks William_Wallace thanked for this post

  8. #8
    William_Wallace's Avatar
    Join Date
    Jun 2017
    Posts
    737
    Post Thanks / Like

    Re: DIY mechanic tool needed

    Quote Originally Posted by Oneheadlite View Post
    Just to clarify - you`ve gotten the CV out of the hub and are trying to pull the hub from the bearing, yes?

    Not familiar with the cars you`re working on, but I`ve done a great many wheel bearings.

    If the axle is out of the way:
    My preferred method is to use a bridge setup that presses against the bearing housing to pull the hub out of the bearing. Sometimes bearing housing shape doesn`t allow (don`t have sufficient area to press against - side note: Never press on brake caliper mounting ears! Seen a lot of guys do a lot of damage trying to do press work...) ; in those cases we just do the good old fashioned slide hammer approach. Most slide hammer kits you buy have really light duty slides (3lbs) - if you can, find something heavy to add (old brake rotor/etc) to increase your impact to help pop it out.

    Google: Hub Grappler - in that image you`ll see the bridge setup I`m referring to. That`s the kit we use at our shop. In the DIY realm, I`d call around and see what your local parts stores rent out and look at "renting" a wheel bearing tool. Usually you "purchase" the tool, then they give you your money back when you return it.

    If the axle is refusing to come out of the hub, let me know and I can try to explain what I`ve done for that. Short version: Snap on has a forcing screw you use in the slide hammer adapter you bolt to the hub. Apply force with that, then shock the axle with strikes on the end of the forcing screw with a brass hammer. Also, penetrating oil and time are your friends...

    Let me know what step you`re at and I`d love to help.
    great info hub grappler is something I would purchase and I have 2 of the 4 hub with cv axels rust welded in good heat and air hammer couldn’t get it to push out.thanks a ton the hub grappler look beefy to hold up for years I can usually get hubs off by the reverse stud trick but not here too much rust.

  9. #9
    William_Wallace's Avatar
    Join Date
    Jun 2017
    Posts
    737
    Post Thanks / Like

    Re: DIY mechanic tool needed

    I already had a multi day battle with the inner tie rods the was an excessive amount of red thread locker and I had to do keep repeated high heat to them. All the special tools failed I ended up grinding a slot in them and used air hammer to lefty Lucy them off little by little and kept them hot once off I realized it was caked very bad with red thread locker.

  10. #10
    Sizzle Chest's Avatar
    Join Date
    Apr 2012
    Location
    SW Florida
    Posts
    2,616
    Post Thanks / Like

    Re: DIY mechanic tool needed

    The old heat wrench! Oxy/Acetylene torch. Rose bud end. Heat it up and slide hammer that sucker off!
    Scott Harle
    www.autodermatology.com
    Autodermatology
    Serving Naples and SW Florida
    Instagram: www.instagram.com/autodermatology
    Facebook: www.facebook.com/autodermatology
    Likes William_Wallace liked this post

  11. #11
    William_Wallace's Avatar
    Join Date
    Jun 2017
    Posts
    737
    Post Thanks / Like

    Re: DIY mechanic tool needed

    Quote Originally Posted by Sizzle Chest View Post
    The old heat wrench! Oxy/Acetylene torch. Rose bud end. Heat it up and slide hammer that sucker off!
    I put it on my list and hope Santa bring me a big boy torch because I’m over here with a propane torch!

 

 

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Similar Threads

  1. The perks of being a mechanic
    By ShaneB in forum Everything Else
    Replies: 12
    Last Post: 10-20-2015, 04:08 PM
  2. G6 Mechanic friend
    By baker in forum Click & Brag -The Detailers Showcase
    Replies: 2
    Last Post: 09-09-2009, 02:27 AM
  3. Mechanic/scratches
    By LQ9SS in forum Car Detailing
    Replies: 3
    Last Post: 09-25-2007, 08:48 PM
  4. mechanic in chandler, az
    By medic in forum Car & Driver
    Replies: 0
    Last Post: 03-31-2005, 02:25 AM
  5. Replies: 6
    Last Post: 04-28-2004, 04:26 PM

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •