Big new order today

**Gonzo** · 04-01-2005, 08:17 PM

PO106FF x 1, PO85RD x 2, Finishing Touch Glaze x 2, FMJ & Hight Gloss Acrylic Shield, both x 2

**6']['9** · 04-01-2005, 08:22 PM

and you ordered that form where? What is the PO106FF for?

**01bluecls** · 04-01-2005, 08:24 PM

I need to order the PO85RD I really want to try it! Where did you get yours from and how much? What size bottle did you get also? You are officially a Menerna Freak!

jk

**6']['9** · 04-01-2005, 08:25 PM

CMA sells the PO85RD for $45 and it only comes in quarts.

**Gonzo** · 04-01-2005, 08:57 PM

You get it here

http://www.properautocare.com/pofornececlc.html

CMA says

"PO85RD is the lightest cut, best used for burnishing an almost perfect surface to a glass-like finish. PO106FF contains a higher percentage of powder for more power. It is designed to remove very fine (3000 grit) swirls and blemishes. If you`re a Menzerna customer, these polishes are like Final Polish II on steroids!

**6']['9** · 04-01-2005, 10:51 PM

do you really think theres a difference between the FPII and PO106?

**l33** · 04-01-2005, 10:55 PM

Menzerna crazy.... good stuff.

**05Sleeper** · 04-01-2005, 10:58 PM

I would have NO IDEA howto use this stuff. Please do so and fill us in. t should be a very interesting project for you!

**6']['9** · 04-01-2005, 11:05 PM

with a rotory is the best way to use it.

**Neo62381** · 04-01-2005, 11:24 PM

Pics of a car that these products have been used on would be exceptional, just a newb`s opinionm tho

**JaCkaL829** · 04-01-2005, 11:54 PM

Nice order gonzo, the folks at Menzerna must be happy

Not sure if this was discussed in a previous thread or not but I just saw on PakShak`s website under new products that hes going to have limited supply of the PO85RD and P0106FF in April. Might be a good time to put an order through, especially if your trying to save on shipping, PakShak has one of the biggest selections of brands I think out of all the vendors.

**MS22** · 04-02-2005, 12:34 AM

That is a monster order! I want to try those ceramiclear polishes badly but can not see spending $50 on a bottle of polish, way too broke right now.

Hope you plan on being busy with all that FMJ too, it lasts forever.

**03COBRA** · 04-02-2005, 12:42 AM

You shouldn`t have made that order for PO85RD......you will never go back!

**Gonzo** · 04-06-2005, 08:16 PM

You can see the pix here

http://www.svt-enthusiast.com/module.../Gonzo?page=20

left click to isolate thumbnail and left click again to see full 6MB

Amazing stuff!

:bounce

First up LC white pad and PO106FF over whole hood

Second up LC gray pad and PO85RD over whole hood

Third up Menzerna Glaze by hand with a 4" foamy

Last up menzerna FMJ by hand with a 4" foamy

Both polished stayed "wet` a long time, with the PO85RD just about completely disappearing and both were wiped off with virtually no effort using a clean MF. Used the Metabo only, speed 4 for the PO85RD and started @ 4 going up and down the back and forth at right angles; then up to 5 after that for 2 more "wind direction" passes. Glaze and FMJ went on like a breeze and came off even easier... After the FMJ I think it is every bit as slick as UPP.

I likey!!!!!

Over the next few days I`ll put another couple of FMJ`s then start an environmental test - living in my driveway 24/7. I`ll keep eveyone posted as to how it lasts and performs