Does anyone have any experience with this product?
Looking to clean up lightly oxidized cast aluminum in engine compartments.
I found one US distributor that stocks it. At $22.00
Sent from my iPhone using Tapatalk
Does anyone have any experience with this product?
Looking to clean up lightly oxidized cast aluminum in engine compartments.
I found one US distributor that stocks it. At $22.00
Sent from my iPhone using Tapatalk
Sounds like their version of the acidic metal treatment that`s used for so many things.
What do their instructions say about rinsing/etc. to neutralize it?
Post Thanks / Like - 1 Likes, 0 Thanks, 0 DislikesLEDetailng liked this post
According to the MSDS Alubright is a combination of Phosphoric and Hydrofluoric Acid with a PH of 1.0
Direction on usage are as follows:
Dilute at 1-1 ratio with Water and a dwell time of no more than 1 to 2 minutes. Rinse off with water.
Post Thanks / Like - 0 Likes, 1 Thanks, 0 DislikesLEDetailng thanked for this post
It sounds similar to the stuff I use, if not identical. I`d be very, *VERY* careful what you get that on.
Heh heh, that "rinse off.." could well prove easier said than done, and where`s the rinsed off stuff supposed to go? Someplace where it don`t cause any issues I hope.Direction on usage are as follows:
Dilute at 1-1 ratio with Water and a dwell time of no more than 1 to 2 minutes. Rinse off with water.
No, not flaming the stuff, I have a product called "Metal Blast" that`s about the same thing. But I`m very, very careful about what I do with it. Heh heh, I sure would *NOT* "spray and brush" anything on a vehicle that I was gonna concours! I basically never spray such products, always brushing/dabbing/wiping them on so I have complete control over where the stuff goes.
Is that dilution aluminum-specific?
Post Thanks / Like - 1 Likes, 0 Thanks, 0 DislikesLEDetailng liked this post
According to Arnold Industries website General ratios: 1-1 is for Keying the Surface. 1-20 is for Polishing and Cleaning.
Referred to as an Acid Detergent for Aluminum, Copper Zinc, etc.
Looks too Problematic to me. 1L ALUBRIGHT ALUMINIUM CLEANER | Arnold Products Limited
Post Thanks / Like - 1 Likes, 0 Thanks, 0 DislikesLEDetailng liked this post
Marine Clerk- Huh, "acid detergent"..that`s a new one for me. Well, OK...you do rinse off detergents!
I always have something like that on the shelf, but I seldom use it for anything other than those rare Big Projects. Last time was to clean up the Tahoe`s tailpipe a little.
But if I`m not careful I`ll start to think how nicely something like this might shine up those aluminum heads...
I do use a mildly acidic product kinda like this (KRC7, it has Glycolic and Sulfanic acids) to remove the blooming from zinc-plated stuff and I guess this might not be too different once you consider dilution. Never tried KRC7 on the heads, maybe I oughta some time, but it`s awfully mild...
Post Thanks / Like - 1 Likes, 0 Thanks, 0 DislikesLEDetailng liked this post
Looks similar to the Flitz Metal Pre-Cleaners. There is one for all metals and one for aluminum. I use them on motorcycle details. Cuts way down on the amount of metal polishing needed. Comes out better too.
Post Thanks / Like - 1 Likes, 0 Thanks, 0 DislikesLEDetailng liked this post
Well, I usually wash the bike`s after using them and the initial rinse. I usually will also use a metal polish afterwards. So I have not really thought about the neutralizing part of it much. I will use P21S Polishing soap as a first step on the chrome. I love that stuff.
DBAILEY- Ah, sounds like the wash/rinse is sufficient neutralizing.
You don`t use the P21s Polishing Soap on aluminum?
I will if it is a piece that I can use that P21S scrub sponge on, but the FlitZ PreClean for aluminum being a spray allows me to get into all the nooks and crannies of a motorcycle. I don`t do many motorcycles. I only done maybe a half dozen in the past, but a friend (co-worker) with a motorcycle repair shop has started giving me referrals on bikes since he does not have the time to do them himself, but doesn`t want to not provide that service. Motorcycle guys seem more willing to pay for an extensive detail than car guys so far.
Post Thanks / Like - 1 Likes, 0 Thanks, 0 DislikesLEDetailng liked this post
DBAILEY- Ah, OK, I see...and yeah, I`ve never done a motorcycle but always figured they`d be a *lot* of work to get truly nice.
Somehow I`d always thought that bikers did such stuff themselves as part of the "pick up your own brass" mentality...my neighbors with the (loud) Harleys spend forever on `em.
There are currently 1 users browsing this thread. (0 members and 1 guests)
Bookmarks