Polycharger Wax Booster Giveaway ADDYDADDY REVIEW POST 42

[addysdaddy]

sooooo, when is the announcement? I`m all ready to try it out and write my review. haha

[Wheelzntoys]

I`m charging my camera! So ready!

[Todd@RUPES]

sooooo, when is the announcement? I`m all ready to try it out and write my review. haha

Addy, you won!!!!

Send me your mailing info and I will get this out to you ASAP!

[colinpd137]

Congrats Addy!

[Van185]

Congrats to Andy. Can`t wait to see the review.

[addysdaddy]

LOL, I cannot thank you enough Todd. PM sent. I`ll try and do the review justice and again my sincerest thanks. This is honestly the first thing I`ve ever won, so I`m truly speechless.

[Wheelzntoys]

Congrats! Will wait for review and then decide to buy

[ihaveacamaro]

congrats!

[Merlin]

Congrats!

[Ronkh]

Congrats!

[Pats300zx]

Congrats !!!!

[addysdaddy]

Polycharger test

The test vehicle is my neighbors neglected Ranger Rover. Shows the condition of the hood after a quick waterless wash. Feels like sandpaper


To get the paint ready to accept the sealant, used ONR solution and clay bar.



WG Paint Cleanser applied by hand with a damp mf towel


Inspecting the paint to confirm that it passed the plastic baggie test.


WG Sealant and CH2 Polycharger solution. Will apply by hand via foam pad


Mixed test solution of CH2 & WG Deep Gloss Sealant 3.0 and finished applying both halves of the test at 2pm



The drivers` side half of the hood applied with polycharger version. Passenger side applied with straight sealant that`s not been polycharged.


Performed swipe test after allowing the LSP to set up for 45 minutes and the panel was good to go. Two gold jr mf, short nap for first wipe and long nap for final wipe. One observation worth noting even now is that the polycharged side was much easier to remove then the straight sealant. IMO, that alone would make me consider the product-stay tune as I will continue to update in the next several weeks.



Beauty shots of the freshly coated panel.







My plan is to wait 30 days and do both a visual, feel and water bead test and report back. Just would like to say thanks again to Todd for the kit and hope this review will ultimate help.

[Todd@RUPES]

Polycharger test

The test vehicle is my neighbors neglected Ranger Rover. Shows the condition of the hood after a quick waterless wash. Feels like sandpaper


To get the paint ready to accept the sealant, used ONR solution and clay bar.



WG Paint Cleanser applied by hand with a damp mf towel


Inspecting the paint to confirm that it passed the plastic baggie test.


WG Sealant and CH2 Polycharger solution. Will apply by hand via foam pad


Mixed test solution of CH2 & WG Deep Gloss Sealant 3.0 and finished applying both halves of the test at 2pm



The drivers` side half of the hood applied with polycharger version. Passenger side applied with straight sealant that`s not been polycharged.


Performed swipe test after allowing the LSP to set up for 45 minutes and the panel was good to go. Two gold jr mf, short nap for first wipe and long nap for final wipe. One observation worth noting even now is that the polycharged side was much easier to remove then the straight sealant. IMO, that alone would make me consider the product-stay tune as I will continue to update in the next several weeks.



Beauty shots of the freshly coated panel.







My plan is to wait 30 days and do both a visual, feel and water bead test and report back. Just would like to say thanks again to Todd for the kit and hope this review will ultimate help.

Thank you for doing this, looking forward to the results!

[Merlin]

Does anyone know how Polycharger would act with BFWD AFPP?
How soon after the first coat can you layer another coat of BFWD?
Will Polycharger increase the durability/longevity of BFWD AFPP?

_____________


Merlin

[Swanicyouth]

Nice post... Buy I gotta tell you, claying with a ring is asking for disaster