Results 1 to 11 of 11
  1. #1
    I like teeth ihaveacamaro's Avatar
    Join Date
    Oct 2012
    Location
    Ft. Lauderdale, Fl
    Posts
    1,556
    Post Thanks / Like

    Tips on using MF pads?

    I`m going to be using Optimum MF pads for the first time. I don`t have compressed air to clean.

    What are some tips for general usage, finer tips for advanced usage and tips for cleaning them?

    Thanks!

  2. #2
    Ummm.... Ya..... TroyScherer's Avatar
    Join Date
    May 2010
    Location
    Ohio
    Posts
    4,916
    Post Thanks / Like

    Re: Tips on using MF pads?


    I would clean them after every panel or section. The cleaner they stay the better they work.


    Try wrapping a roll of tape with aMF towel. Turn the polisher on lower and rub the towel over the pad while laying flat. it is simple yet effective.

  3. #3
    AMG Classic Car Detailing Old Pirate's Avatar
    Join Date
    Feb 2008
    Location
    Sunny Florida
    Posts
    11,199
    Post Thanks / Like

    Re: Tips on using MF pads?

    Great idea there Troy, or you can invest in a Canless Air system. It`s environmentally friendly!
    AutopiaForums is the place to be.
    Remember to Shop Autopia-CarCare.com for your Detailing Needs!

  4. #4
    Rocket's Avatar
    Join Date
    Jun 2011
    Location
    Texas
    Posts
    2,033
    Post Thanks / Like
    A bug sponge has been suggested several times.

  5. #5
    I like teeth ihaveacamaro's Avatar
    Join Date
    Oct 2012
    Location
    Ft. Lauderdale, Fl
    Posts
    1,556
    Post Thanks / Like

    Re: Tips on using MF pads?

    Alright I`m probably going to get this [ame=http://www.amazon.com/Metro-Vacuum-ED500-500-Watt-Electric/dp/B001J4ZOAW/ref=sr_1_1?ie=UTF8&qid=1352217487&sr=8-1&keywords=Metrovac+duster]Amazon.com: Metro Vacuum ED500 DataVac 500-Watt 0.75-HP Electric Duster 120-Volt: Home Improvement[/ame] for cleaning.

    Any tips on using the MF pads ie speed/pressure on pc?

  6. #6
    I like teeth ihaveacamaro's Avatar
    Join Date
    Oct 2012
    Location
    Ft. Lauderdale, Fl
    Posts
    1,556
    Post Thanks / Like

    Re: Tips on using MF pads?

    bumpity bump

  7. #7

    Join Date
    Feb 2011
    Posts
    250
    Post Thanks / Like

    Re: Tips on using MF pads?

    Besides compressed air, the Megs pad brush is what I use and it works almost as well as the air does. Use after every pass, not every panel. I clean the pad before putting on more compound or polish.

  8. #8
    Ummm.... Ya..... TroyScherer's Avatar
    Join Date
    May 2010
    Location
    Ohio
    Posts
    4,916
    Post Thanks / Like

    Re: Tips on using MF pads?

    Quote Originally Posted by ihaveacamaro View Post
    Any tips on using the MF pads ie speed/pressure on pc?

    Now I have not used the Opti MF Pads, but I have used the Meg`s version many times.

    1. What machine are you using? I am using a PCxp.


    For speed I would suggest around 4-5. I have used speed 6 but only in limited bursts. When used at FULL BLAST the Meg`s tend to haver issues. So med -full power.

    As far as pressure. I suggest meduim for most uses and only real heavy pressure in short burst as well. You want to let the pad do the work.


  9. #9
    My name is Mike mjlinane's Avatar
    Join Date
    Jul 2011
    Location
    Round Rock, TX
    Posts
    4,071
    Post Thanks / Like

    Re: Tips on using MF pads?

    Following on Troy`s comment, I stick with a 5" pad or smaller on my PCXP. Except on curvy spots, I can use a 6" on my GG6. I apply pressure just until the motor starts to bog but not enough to stop the pad.

    As has been mentioned, they work more efficiently with frequent cleaning.

  10. #10

    Join Date
    May 2011
    Posts
    189
    Post Thanks / Like

    Re: Tips on using MF pads?

    i thinks pinnacle makes a yellow foam block for bugs that you can use and /or pad brush

  11. #11
    I like teeth ihaveacamaro's Avatar
    Join Date
    Oct 2012
    Location
    Ft. Lauderdale, Fl
    Posts
    1,556
    Post Thanks / Like

    Re: Tips on using MF pads?

    I am using the PCXP. Thanks for the tips on how to use them Troy and mjlinane

 

 

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Similar Threads

  1. Surbuf Buffing Pads: Tips and Tricks for Maximum Cut!
    By Todd@RUPES in forum Paint Correction and Gloss Enhancement
    Replies: 26
    Last Post: 04-16-2012, 09:11 AM
  2. Tips On Rotary Pads And Tips
    By schmitt55 in forum Machine Polishing & Sanding
    Replies: 0
    Last Post: 08-05-2008, 07:20 PM
  3. Pads absorbing too much, tips to help?
    By Marc Hufnagel in forum Car Detailing
    Replies: 4
    Last Post: 11-22-2006, 10:17 PM
  4. Q-Tips with Round and Pointed Tips at Walgreens
    By imported_hooked in forum Good Deals
    Replies: 4
    Last Post: 08-18-2006, 10:39 AM
  5. Need tips on cleaning buffing pads.
    By AdamJoe in forum Car Detailing
    Replies: 6
    Last Post: 12-31-2003, 01:45 AM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •