Post Thanks / Like - 1 Likes, 0 Thanks, 0 Dislikesnoorth liked this post
Carzilla is my main source of detailing products. They have an impressive amount of brands.
Probably have to wait until next spring to try the UNO advanced now for me. I think i will be trying it.
I actually polished off 2 coats of cancoat off my bonnet yesterday! I had like 10 high spots! I`m so over ceramic coatings lol
Its sitting now with gyeon primer - i`m half thinking to just top it with polish angels rapidwaxx. I even thought of putting a paste wax on it lastnight lol
The roof and trunk lid look fine however, they were also coated with cancoat.
I don`t recall what I got out of a test panel. I`d say 3 months seems about right, though. The cars i`ve used it on were one and done. I never see them again.
Haven`t tried Feynlab RW. Sounds like a decent cleaner, but I`m plenty happy with McKees 37. Also use ONR, and Blackfire`s RW...but McKees is my current go-to (for it`s leave nothing behind properties)
Can`t clean glass with the Feynlab? That`s not good. I love RW for cleaning glass.
Post Thanks / Like - 1 Likes, 0 Thanks, 0 DislikesStokdgs liked this post
Feynlab Pure Rinseless is very nice but be aware it will immediately degrade anything other than a ceramic coating. It`s strong stuff so you`ll be using your topper every time with it. You may be better off with N914, ONR, Absolute, or any of the others that aren`t quite as potent. Feynlab cleans extremely well but it`s really meant to be used on a ceramic coated card.
Feynlab is very streaky and grabby on glass for some reason.
and...here it is:
RUPES UNO Advanced
I will probably run a test on 1-2 panels next year just for some fun. UNO advanced topped with rapidwaxx. Not sure if i should wait at least 4 hours or less.
More information to follow i`m sure. TRC might put out something or rupes themselves.
At last we have proper protection in a Car Polish | Rupes Uno Advanced - YouTube
Water sheeting is decent but more sealant than coating like.
Topping with RW seems like a good plan
Sent from my iPhone using Tapatalk
After 4 hours can we put coating on? Or is prep needed
I just watched the new autogeek video with Todd from Rupes. He never mentioned anything about a primer.
AIO, finishing step of a 2-3 step job and to repair existing coatings.
If it can be use to repair existing coating i doubt it cuts very much.
You can probably compare it with carpro essence+ with some very light abrasives...
I think i will try labocosmetica`s fiero frankly. You don`t have to wait to apply a coating or sealant and i hope it has a half decent cut.
They did put it up against the "marketing leading competition" in one video - it was probably essence or gyeon primer - to demonstrate it had more cut. So it was a consideration to get a primer with a little cut.
Gyeon primer is super fine.
Ordered some. I think I’ll throw some ocw or opti seal over it. If I get 4-6 months I’ll be happy.
2021 VW GLI Autobahn
Pure Gray/Black
Protected by 303 GraphenePost Thanks / Like - 1 Likes, 0 Thanks, 0 Dislikesnoorth liked this post
So......got to use UNO Advanced today on my daughters Hyundai Sonata. Product is very thin and watery out of the bottle.....not what I like, but not unlike Uno Protect. When matched with a 50/50 Urofiber pad, it removed some water spots (not etched) and some very light surface defects. I used a Griots yellow polishing pad on the rest of the car. Goes on easy, comes off relatively easy. Surface is slick, although not 3D Speed slick. Will revisit it when it has had it`s four hours of cure time. The directions say to leave it on al least 15 minutes before wipe off. I left some on around 30 minutes to see how removal was......basically the same as the rest of the car. If it lives up to it`s claims of long-term protection, I can see it as a viable option.
Post Thanks / Like - 2 Likes, 0 Thanks, 0 Dislikesnoorth, MisterSnoop liked this post
There are currently 1 users browsing this thread. (0 members and 1 guests)
Bookmarks