What about BH followed by Collinite 476.
What about BH followed by Collinite 476.
I received the BH and EX today and used both. Perhaps I didn`t apply correctly, but I saw no visible improvement in the swirls.
I just applied to the hood. I washed the entire hood, then clayed the entire hood and washed again. Then I applied Klasse AIO. Then I applied the BH to just one half of the hood and saw no improvement. I applied and let it sit for about a minute, and buffed off. I did this 3 more times and still saw no improvement. At this point I added the EX sealant, and that didn`t seem to add any filling either. I then added 2 layers of Souveran, and still no filling.
The only positive I noticed from using the Poorboy`s products was that flakes in the paint seem to pop out a bit more now. But I really saw no filling of the swirls. Did I do something wrong?
Formerly the "Best Detailer", now just Super Wax Waster Man. Not necessarily tactful, but normally right. It`s good to be da King !!!
Probably won`t come up due to the `
So here are some pics:
Dealer washed car with brush, then dried....... Looked a lot worse in person:
After 1 app of BH
After 2 apps of bh
After Natty`s blue
Next day in sun
Formerly the "Best Detailer", now just Super Wax Waster Man. Not necessarily tactful, but normally right. It`s good to be da King !!!Post Thanks / Like - 1 Likes, 0 Thanks, 0 DislikesMackCollier liked this post
I went back and checked the thread and I wasn`t very clear. I had asked about using the Klasse twins and I believe Ron said no, but I assumed that meant that Klasse SG was the problem, but it looks like both you and he were actually saying that NEITHER AIO or SG would work well with BH?
Just to clarify....I can`t use Klasse All-In-One with the BH?
Assuming that`s the case, what`s the best way to remove AIO? Yes I am well on my way to wasting wax
To add (in case another point of confusion):
The Blackhole should be the first thing applied to the clean / clayed paint, then your Sealant (EX, FK1000p, Collinite 476, etc.), then your wax topper (Souveran).
As Poorboys mentioned, applying BH over an existing selant or wax won`t let the fillers do their job.
Nick
Post Thanks / Like - 1 Likes, 0 Thanks, 0 DislikesMackCollier liked this post
Original paint. Does Poorboy`s make a product that would clean the AIO off the paint without affecting the clearcoat? I really don`t want to remove any of the clearcoat, I would much rather fill the swirls then seal, which is why I bought BH and EX to begin with. Thanks!
life is short ..do it while you can
e-mail info@poorboysworld.com
Post Thanks / Like - 1 Likes, 0 Thanks, 0 DislikesMackCollier liked this post
Thanks, I noticed the Poorboy`s polish w carnuba - Poorboy
OK....just so I don`t screw up again. If I get the Polish w/Carnauba, I wash the car, then apply the polish THEN apply the Black Hole THEN apply the EX sealant THEN top with Souveran?
All that and I`m good?
Post Thanks / Like - 1 Likes, 0 Thanks, 0 DislikesPoorboy liked this post
life is short ..do it while you can
e-mail info@poorboysworld.com
Post Thanks / Like - 1 Likes, 0 Thanks, 0 DislikesMackCollier liked this post
Post Thanks / Like - 3 Likes, 1 Thanks, 0 DislikesRonkh thanked for this post
Formerly the "Best Detailer", now just Super Wax Waster Man. Not necessarily tactful, but normally right. It`s good to be da King !!!Post Thanks / Like - 3 Likes, 0 Thanks, 0 Dislikes
There are currently 1 users browsing this thread. (0 members and 1 guests)
Bookmarks