Mad iX
06-10-2005, 03:06 AM
Got to detail an Evo V today. Unfortunately, duty called and I had to stop when I was just getting into it. I`ll probably be resuming this sometime next week. Nice car but unfortunately a lot of signs of neglect.
Doesn`t look too bad here. In fact it looks pretty good. That`s what I thought when I first saw it.
http://gallery.pixelstreak.com/gallery/albums/album11/01_G.jpg
However, on closer inspection ...
Smudge is from a test of ScratchX, which didn`t do much.
http://gallery.pixelstreak.com/gallery/albums/album11/02_G.jpg
More ...
http://gallery.pixelstreak.com/gallery/albums/album11/03_G.jpg
Started with a wash (2-bucket method) with EO.
Almost non-existant beading. 8O
http://gallery.pixelstreak.com/gallery/albums/album11/04_G.jpg
After rinse, left the car wet and clayed with Meg`s QD and Claymagic blue.
Horizontal surfaces were rough but nothing the clay couldn`t handle.
Also visible is the trim which was moderately faded. PB TR did well but I had to buff it off almost right away due to lack of time.
http://gallery.pixelstreak.com/gallery/albums/album11/05_G.jpg
Paint defect under the CC.
http://gallery.pixelstreak.com/gallery/albums/album11/06_G.jpg
Masked off the vents.
http://gallery.pixelstreak.com/gallery/albums/album11/07_G.jpg
Neeeed ... to ... polishh ...
http://gallery.pixelstreak.com/gallery/albums/album11/08_G.jpg
I`d only just started attacking the hood with SSR 2.5 when I got a phone call from work. Finished off the hood quickly, noticeably diminished the swirls but still plenty left. Sorry but haven`t got pics of that, but the CC seemed quite thin due to lack of depth even on black. Hopefully a 2nd round of SSR 2.5 and finishing up with SSR 1 will yield some more satisfactory results. If not, then I`ll have to break out DACP or even IP.
Also, it`s got an aluminium wing, which has a couple of stains. It`s not polished aluminium, more of a matt finish. I tried clay but it didn`t touch them. Anybody know of a product I can try? I was thinking AIO or even VM but wasn`t able to try them out.
Doesn`t look too bad here. In fact it looks pretty good. That`s what I thought when I first saw it.
http://gallery.pixelstreak.com/gallery/albums/album11/01_G.jpg
However, on closer inspection ...
Smudge is from a test of ScratchX, which didn`t do much.
http://gallery.pixelstreak.com/gallery/albums/album11/02_G.jpg
More ...
http://gallery.pixelstreak.com/gallery/albums/album11/03_G.jpg
Started with a wash (2-bucket method) with EO.
Almost non-existant beading. 8O
http://gallery.pixelstreak.com/gallery/albums/album11/04_G.jpg
After rinse, left the car wet and clayed with Meg`s QD and Claymagic blue.
Horizontal surfaces were rough but nothing the clay couldn`t handle.
Also visible is the trim which was moderately faded. PB TR did well but I had to buff it off almost right away due to lack of time.
http://gallery.pixelstreak.com/gallery/albums/album11/05_G.jpg
Paint defect under the CC.
http://gallery.pixelstreak.com/gallery/albums/album11/06_G.jpg
Masked off the vents.
http://gallery.pixelstreak.com/gallery/albums/album11/07_G.jpg
Neeeed ... to ... polishh ...
http://gallery.pixelstreak.com/gallery/albums/album11/08_G.jpg
I`d only just started attacking the hood with SSR 2.5 when I got a phone call from work. Finished off the hood quickly, noticeably diminished the swirls but still plenty left. Sorry but haven`t got pics of that, but the CC seemed quite thin due to lack of depth even on black. Hopefully a 2nd round of SSR 2.5 and finishing up with SSR 1 will yield some more satisfactory results. If not, then I`ll have to break out DACP or even IP.
Also, it`s got an aluminium wing, which has a couple of stains. It`s not polished aluminium, more of a matt finish. I tried clay but it didn`t touch them. Anybody know of a product I can try? I was thinking AIO or even VM but wasn`t able to try them out.