holland_patrick
05-17-2005, 09:20 PM
Well Now that i have used the Happy threesome I`ll let everyone in on the scoop.
Labeling-nice clear and tasteful
Directions.. Here is where we go bad. Now I`m a firefighter and we normally take stuff at face value so when you tell me not to exceed 4,500 RPM(this is the probelm here) I`m looking how to crank up the speed on my 1000-3000 RPM rotary which I use. This could be a probelm for newwer detailers but I ran the polishes at 1,200-1500 RPM just so you know.
Here is the starting picture
http://i4.photobucket.com/albums/y136/holland_patrick/IMG_2570.jpg
Now The Super swirl elimtator It says to pretty much load the crap out of the pad at first. 3 lines on the outside of a cutting pad which and went to town.
I found it work for a long time (even after the first load up) and seemed to cut well but I has a lot of hazing.. Just for HAHA`s i switched to a Polishing pad...Much better...
after SSR
http://i4.photobucket.com/albums/y136/holland_patrick/IMG_2571.jpg
Mild swirl elimtator
This again had you load up the pad and got to town although they want you to use a light cutting pad I didn`t have any so I used a polishing pad.. this went well and cut the swilrs down more..
http://i4.photobucket.com/albums/y136/holland_patrick/IMG_2572.jpg
Now for the Final Finishing Polish I really like this stuff I made the paint squeeky clean and finished up the polishing really nice. I would love to have some more of this stuff(AIO replacment???)
http://i4.photobucket.com/albums/y136/holland_patrick/IMG_2573.jpg
Now you might ask did I like them.. well yes I did they were easy to use and did a good job. Now would i use the on an everyday working detail NOPE I found going over the same panel 3 times Sucked and when your geting an hourly rate it`s not an option. Would I use this for a car that I`m going to drive HELL YA.. The Tri kicked *** and On a well preped car your going to have a Knock out. (Just for fun I used BIG O on one door and it did the same if not better then the trio in less time 1/3)
Patrick
Labeling-nice clear and tasteful
Directions.. Here is where we go bad. Now I`m a firefighter and we normally take stuff at face value so when you tell me not to exceed 4,500 RPM(this is the probelm here) I`m looking how to crank up the speed on my 1000-3000 RPM rotary which I use. This could be a probelm for newwer detailers but I ran the polishes at 1,200-1500 RPM just so you know.
Here is the starting picture
http://i4.photobucket.com/albums/y136/holland_patrick/IMG_2570.jpg
Now The Super swirl elimtator It says to pretty much load the crap out of the pad at first. 3 lines on the outside of a cutting pad which and went to town.
I found it work for a long time (even after the first load up) and seemed to cut well but I has a lot of hazing.. Just for HAHA`s i switched to a Polishing pad...Much better...
after SSR
http://i4.photobucket.com/albums/y136/holland_patrick/IMG_2571.jpg
Mild swirl elimtator
This again had you load up the pad and got to town although they want you to use a light cutting pad I didn`t have any so I used a polishing pad.. this went well and cut the swilrs down more..
http://i4.photobucket.com/albums/y136/holland_patrick/IMG_2572.jpg
Now for the Final Finishing Polish I really like this stuff I made the paint squeeky clean and finished up the polishing really nice. I would love to have some more of this stuff(AIO replacment???)
http://i4.photobucket.com/albums/y136/holland_patrick/IMG_2573.jpg
Now you might ask did I like them.. well yes I did they were easy to use and did a good job. Now would i use the on an everyday working detail NOPE I found going over the same panel 3 times Sucked and when your geting an hourly rate it`s not an option. Would I use this for a car that I`m going to drive HELL YA.. The Tri kicked *** and On a well preped car your going to have a Knock out. (Just for fun I used BIG O on one door and it did the same if not better then the trio in less time 1/3)
Patrick