Optimum Gloss Coat

[CleanIt]

I decided to try the new Gloss Coat that was recently reformulated a few months ago. Truck was prepped with Hyper Polish and OPT Pain Prep. I applied 2 coats, an hour apart. It rained 24 hours later and I grabbed a beading shot. I drove the truck shortly after to dry it. Shower was brief. Gloss Coat can technically get wet after 8 hours, or an hour after if OS is applied.

Application was simple, however I didn`t use quite enough product. Only 8cc`s were used so I`m not expecting the longevity to hit 2 years. I probably should have used at least 10cc`s.

https://www.autopia.org/forums/attachment.php?attachmentid=37890&stc=1

[The Guz]

Should be ok. But it is good practice to apply opti-seal as an insurance measure to avoid the coating developing spots during the curing time. Good luck with gloss coat. It seems they didn`t make it more durable but rather change the resins. Could be due to supply chain issues but who really knows.

[Coatings=crack]

Not trying to be negative but honest I don’t think those beads hold a candle to CqUk3 freshly applied. Hope it holds up for you.

I’m afraid i may think the same of Evo when I apply it.


Sent from my iPhone using Tapatalk

[CleanIt]

It was a last minute decision to try it. Figured I`d go with the one of the easier coatings to apply being I never used a coating before. Only regret was not applying it a bit heavier for the first layer.

[Coatings=crack]

It was a last minute decision to try it. Figured I`d go with the one of the easier coatings to apply being I never used a coating before. Only regret was not applying it a bit heavier for the first layer.

Again, Heavier applying wouldn’t make it work better.

Even with a second coat alot of folks don’t rhink you get an actual second layer. Just insures you get a nice, full even coverage. Personally not sure.

Would do second coat just because manufacturer says so. Does it give me thicker coat or are the just trying to sell more product? [emoji2369]


And the way i was expained to that made finally believe thicker is not better.

Picture laying on a layer an inch thick. The coating has to bond to the paint so only the very thin layer of nano particles are bonding to the paint.

Anything on top weather a micro thin layer or an inch off product will just be being wiped off. Only after that layer partially bonds (however long manufacturer recommends to wait) then you can add another layer that will bond with that.

Thinner is better. Easier to remove. Use the extra to add a second coat the high impact areas.

Sent from my iPhone using Tapatalk

[CleanIt]

Again, Heavier applying wouldn’t make it work better.

Even with a second coat alot of folks don’t rhink you get an actual second layer. Just insures you get a nice, full even coverage. Personally not sure.

Would do second coat just because manufacturer says so. Does it give me thicker coat or are the just trying to sell more product? [emoji2369]


And the way i was expained to that made finally believe thicker is not better.

Picture laying on a layer an inch thick. The coating has to bond to the paint so only the very thin layer of nano particles are bonding to the paint.

Anything on top weather a micro thin layer or an inch off product will just be being wiped off. Only after that layer partially bonds (however long manufacturer recommends to wait) then you can add another layer that will bond with that.

Thinner is better. Easier to remove. Use the extra to add a second coat the high impact areas.

Sent from my iPhone using Tapatalk

Good to know that makes sense. :bigups

[Setec Astronomy]

Use the extra to add a second coat the high impact areas.

That sounds like a great idea! Except someone posted in this thread that that won`t work. Oh wait, that was you, in the same post.

[Coatings=crack]

That sounds like a great idea! Except someone posted in this thread that that won`t work. Oh wait, that was you, in the same post.

Did you read all my words?

“Even with a second coat alot of folks don’t rhink you get an actual second layer. Just insures you get a nice, full even coverage. Personally not sure. “

Didn’t say it wouldn’t work. Said some folks dont think…… Personally not sure…,


Sent from my iPhone using Tapatalk

[The Guz]

Gloss Coat is a one layer coating. No need for a second layer. Back in the Yvan days it was stated a second layer would add more gloss but I never noticed any increase in gloss with a second layer.

The amount used is dependent on the size of the vehicle. Gloss Coat goes a long way as it spreads out further. Also unlike other coatings this one is more of a film rather than hardening up.

[bad penny]

A second coat won`t do anything. Ceramic Coatings are meant to be applied thin. As long as you covered all areas you actually applied it correctly. Use what`s left on your wheels or the walls of your shower

[The Guz]

A second coat won`t do anything. Ceramic Coatings are meant to be applied thin. As long as you covered all areas you actually applied it correctly. Use what`s left on your wheels or the walls of your shower

Always best to follow the manufacturers directions. Whether it’s one layer, two, three, etc.

[bad penny]

Always best to follow the manufacturers directions. Whether it’s one layer, two, three, etc.

OR talk to the chemist in person. Dr G told me all of his coatings only require 1 application.
Something ain`t right with any coating that needs more then 1 application imo.

[The Guz]

OR talk to the chemist in person. Dr G told me all of his coatings only require 1 application.
Something ain`t right with any coating that needs more then 1 application imo.

That’s the optimum coating. Some manufacturers recommend two layers. Most say max 3. Whether it’s right or wrong it’s based on what the manufacturer states.

The opti-coat pro like has I believe a new 3 layer system.