gmblack3
04-12-2010, 01:19 AM
2005 Black Lexus LS430
Client just bought it less then a month ago when he contacted me.
He wanted full exterior correction, full interior with carpet extraction.
http://img717.imageshack.us/img717/5926/img3958g.jpg
http://img594.imageshack.us/img594/8780/img3959.jpg
http://img6.imageshack.us/img6/4350/img3966j.jpg
http://img30.imageshack.us/img30/1945/img3972f.jpg
http://img217.imageshack.us/img217/5194/img3980t.jpg
http://img6.imageshack.us/img6/4920/img3981c.jpg
http://img30.imageshack.us/img30/8906/img3983q.jpg
http://img6.imageshack.us/img6/2900/img3984j.jpg
http://img6.imageshack.us/img6/5846/img3986u.jpg
http://img6.imageshack.us/img6/6967/img3987jd.jpg
http://img217.imageshack.us/img217/3006/img3989.jpg
http://img265.imageshack.us/img265/253/img3991g.jpg
http://img594.imageshack.us/img594/4172/img3993.jpg
http://img202.imageshack.us/img202/2501/img3996b.jpg
http://img191.imageshack.us/img191/6987/img4000b.jpg
http://img30.imageshack.us/img30/1841/img4002k.jpg
http://img576.imageshack.us/img576/9440/img4003.jpg
http://img576.imageshack.us/img576/1126/img4004a.jpg
http://img191.imageshack.us/img191/5903/img4005d.jpg
http://img683.imageshack.us/img683/8913/img4008l.jpg
http://img6.imageshack.us/img6/2895/img4010w.jpg
http://img576.imageshack.us/img576/4977/img4011.jpg
http://img576.imageshack.us/img576/8353/img4013l.jpg
http://img191.imageshack.us/img191/1599/img4017e.jpg
Interior was not too bad to start with.
http://img638.imageshack.us/img638/243/img4020g.jpg
http://img576.imageshack.us/img576/2568/img4024.jpg
http://img263.imageshack.us/img263/7454/img4030o.jpg
Leather and all hard surfaces steamed with my VX5000.
Leather treated with Zaino Z-10
All hard surfaces treated with 1Z einszett Vinyl-Rubber Care & Protectant "Tiefenpfleger."
After a thorough vac, I pretreat all carpet and mats with ultra pac. After a light working in of the pretreat chemicals, by light I mean just brush them in lightly to the fibers in two directions. No need to scrubb.
I filled my Mytee HP60 with Dry Slurry and water. Let it heat up for 15-20 mins while the pretreat chemicals where dwelling. I then purge the extracting tool into a bucket waiting for some very hot water to pass thru.
http://img541.imageshack.us/img541/8351/img4033.jpg
http://img638.imageshack.us/img638/9072/img4035x.jpg
http://img576.imageshack.us/img576/5301/img4036.jpg
http://img6.imageshack.us/img6/2876/img4038ks.jpg
Here is a video of the waste water after extraction:
YouTube- MVI_7967.AVI
After extracting each section I set up air movers/fans to dry the carpet as quickly as possbile.
http://img694.imageshack.us/img694/8825/img4042cq.jpg
http://img263.imageshack.us/img263/639/img4043.jpg
I would let the fans run thru the nite to ensure the carpet was dry.
I was fortunate that Bret could come by the next day to help finish up a few loose ends.
Then it was all about polishing the paint after that.
Here is Bret applying Zaino AIO to the wheels.
http://img188.imageshack.us/img188/7465/img4044m.jpg
Client just bought it less then a month ago when he contacted me.
He wanted full exterior correction, full interior with carpet extraction.
http://img717.imageshack.us/img717/5926/img3958g.jpg
http://img594.imageshack.us/img594/8780/img3959.jpg
http://img6.imageshack.us/img6/4350/img3966j.jpg
http://img30.imageshack.us/img30/1945/img3972f.jpg
http://img217.imageshack.us/img217/5194/img3980t.jpg
http://img6.imageshack.us/img6/4920/img3981c.jpg
http://img30.imageshack.us/img30/8906/img3983q.jpg
http://img6.imageshack.us/img6/2900/img3984j.jpg
http://img6.imageshack.us/img6/5846/img3986u.jpg
http://img6.imageshack.us/img6/6967/img3987jd.jpg
http://img217.imageshack.us/img217/3006/img3989.jpg
http://img265.imageshack.us/img265/253/img3991g.jpg
http://img594.imageshack.us/img594/4172/img3993.jpg
http://img202.imageshack.us/img202/2501/img3996b.jpg
http://img191.imageshack.us/img191/6987/img4000b.jpg
http://img30.imageshack.us/img30/1841/img4002k.jpg
http://img576.imageshack.us/img576/9440/img4003.jpg
http://img576.imageshack.us/img576/1126/img4004a.jpg
http://img191.imageshack.us/img191/5903/img4005d.jpg
http://img683.imageshack.us/img683/8913/img4008l.jpg
http://img6.imageshack.us/img6/2895/img4010w.jpg
http://img576.imageshack.us/img576/4977/img4011.jpg
http://img576.imageshack.us/img576/8353/img4013l.jpg
http://img191.imageshack.us/img191/1599/img4017e.jpg
Interior was not too bad to start with.
http://img638.imageshack.us/img638/243/img4020g.jpg
http://img576.imageshack.us/img576/2568/img4024.jpg
http://img263.imageshack.us/img263/7454/img4030o.jpg
Leather and all hard surfaces steamed with my VX5000.
Leather treated with Zaino Z-10
All hard surfaces treated with 1Z einszett Vinyl-Rubber Care & Protectant "Tiefenpfleger."
After a thorough vac, I pretreat all carpet and mats with ultra pac. After a light working in of the pretreat chemicals, by light I mean just brush them in lightly to the fibers in two directions. No need to scrubb.
I filled my Mytee HP60 with Dry Slurry and water. Let it heat up for 15-20 mins while the pretreat chemicals where dwelling. I then purge the extracting tool into a bucket waiting for some very hot water to pass thru.
http://img541.imageshack.us/img541/8351/img4033.jpg
http://img638.imageshack.us/img638/9072/img4035x.jpg
http://img576.imageshack.us/img576/5301/img4036.jpg
http://img6.imageshack.us/img6/2876/img4038ks.jpg
Here is a video of the waste water after extraction:
YouTube- MVI_7967.AVI
After extracting each section I set up air movers/fans to dry the carpet as quickly as possbile.
http://img694.imageshack.us/img694/8825/img4042cq.jpg
http://img263.imageshack.us/img263/639/img4043.jpg
I would let the fans run thru the nite to ensure the carpet was dry.
I was fortunate that Bret could come by the next day to help finish up a few loose ends.
Then it was all about polishing the paint after that.
Here is Bret applying Zaino AIO to the wheels.
http://img188.imageshack.us/img188/7465/img4044m.jpg