dsms detail - Vengeful Girlfriends...

[dsms]

MAKE FOR DIFFICULT DETAILING :nervous:



Apparently the poor owner of this Scion TC said the "wrong" thing to his girlfriend at the wrong time while she was sitting in the passenger seat.



His girlfriend proceeded to exit the Scion and take off her HIGH HEEL shoe as she walked over to the drivers side door to get some revenge :down



The result...



http://i259.photobucket.com/albums/hh316/nosdrummer91/Scion%20write%20up/DSC_0031-1.jpg



The culprit...



http://i259.photobucket.com/albums/hh316/nosdrummer91/Hollywood_high_heel_sandal.jpg





At first I didn`t believe I could fix the deep scratches caused by the shoe, but the owner begged to do whatever I could so I agreed to the detail ...despite his yelp at my ballpark estimate. In addition to the severe scratches the car in general was in poor condition as it is never garaged and sometimes neglected by other family members the owner informed me.



A shot of the main damage outside



http://i259.photobucket.com/albums/hh316/nosdrummer91/Scion%20write%20up/DSC_0056.jpg



We`ll get to the correction work and wetsanding later, first up is the wash process



The Scion was very dirty with the works: road grime, road salt and heavy brake dust.



I didnt have time to document the wash process on Day 1 of the detail so here is a quick summary.



The DIC 20 and Camspray 1500 PW were a big help during the process as it was freezing temps outside so extra scrubbing and drying weren`t needed



-Poorboys spray and rinse on the wheels

-APC 4:1 on the tires and wheel wells

-Pre foam the paint with a heavy mixture of CG CWG

-Remove road grime w/ Grime Destroyer and PB bug squash

-2 bucket hand wash with gloss it gloss shampoo and 2 shmitts



Before I called it a night I made sure to let the wetsadning paper soak for adequete time so it would be good to go for the following day



Meguiars Uni-Grit 1500, 2000, 2500 and 3000 soaking overnight



http://i259.photobucket.com/albums/hh316/nosdrummer91/Scion%20write%20up/DSC_0076.jpg





Day 2 started the correction work, first the car was clayed



After doing a quick "cellophane test" I found the finish to have a considerable about of contaminants. First I needed to soften up the clay as its been sitting in a cold garage for a while.



Warm water in a pot usually does the trick



http://i259.photobucket.com/albums/hh316/nosdrummer91/Scion%20write%20up/DSC_0071.jpg



I used Gloss It lavender aggressive clay with Megs LT 1:1 for lube



Here is the clay after about 3/4 of the car



http://i259.photobucket.com/albums/hh316/nosdrummer91/Scion%20write%20up/DSC_0084.jpg



After claying came the inspection, my tools of choice were the Highline PTG and the ever so great "Light of Truth" Fenix TK10 ... nothing picks up defects better on metallics



http://i259.photobucket.com/albums/hh316/nosdrummer91/Scion%20write%20up/DSC_0115.jpg



The side fender with moderate swirls under the fenix



http://i259.photobucket.com/albums/hh316/nosdrummer91/Scion%20write%20up/DSC_0102.jpg



There was some sever bird drop etching in several spots of the hood which needed wetsanding attention, before doing large sections of the hood I did a test section, wetsanded and corrected to see what polish and pad combo would work best



I tended to the bird etching on the hood test spot as well, first I sanded with Meguiars Uni-grit 2000grit



http://i259.photobucket.com/albums/hh316/nosdrummer91/Scion%20write%20up/DSC_0106.jpg



http://i259.photobucket.com/albums/hh316/nosdrummer91/Scion%20write%20up/DSC_0105.jpg



http://i259.photobucket.com/albums/hh316/nosdrummer91/Scion%20write%20up/DSC_0143.jpg



I was able to use the same polish and pad combo to remove the sanding marks as well



-Gloss It Extreme Cut w/ a megs burgandy and EVP prime on the Makita.



My Zenith approach was a little different in terms of RPM used because I had Gloss It EVP on the pad when correcting, EVP extends work time and disperses heat so you can polish longer at high speeds without generating excess heat.



900,1200, 1800, 2100 rpm ------ then back down to 1500, 1200 and 900 to finish off



Working the extreme cut on the test spot



http://i259.photobucket.com/albums/hh316/nosdrummer91/Scion%20write%20up/DSC_0109.jpg



Turns out the combo worked excellent, a quick before and after



http://i259.photobucket.com/albums/hh316/nosdrummer91/Scion%20write%20up/DSC_0118.jpg



http://i259.photobucket.com/albums/hh316/nosdrummer91/Scion%20write%20up/DSC_0117.jpg



And under the Light of truth after an IPA wipedown... perfect! You can tell the finish is 100% hologram free because the center LED beam on the Fenix is not refracted on the paint in all directions, you see the beam in a perfect circle which indicates full correction.. mind you these results were after only 1 step correction and the IPA wipedown



http://i259.photobucket.com/albums/hh316/nosdrummer91/Scion%20write%20up/DSC_0110.jpg



I found that combo worked very well so I corrected the rest of the hood, 2 other bird etchings were sanded with either 2000 and 2500grit



Moderate swirling and some deeper RIDS were corrected on the rest of the hood



Before



http://i259.photobucket.com/albums/hh316/nosdrummer91/Scion%20write%20up/DSC_0124.jpg



After



http://i259.photobucket.com/albums/hh316/nosdrummer91/Scion%20write%20up/DSC_0127.jpg



http://i259.photobucket.com/albums/hh316/nosdrummer91/Scion%20write%20up/DSC_0129.jpg

[dsms]

The finish was perfected after only the 1 step, I worked the extreme cut for a very long time and kept jeweling it down until I reached about 1000rpm. To add a bit more depth to the finish I decided to go one more step.



-Gloss It Evolution polish on the cyclo with blue finishing pads, I found the evo polish leaves behind a great finish so I used only a few beads per pad and lightly burnished the paint, no need to tape off sections with the cyclo, on a small hood such as this you can work it all at once. This took about 8 minutes maybe



Working the evolution polish with the cyclo



http://i259.photobucket.com/albums/hh316/nosdrummer91/Scion%20write%20up/DSC_0147.jpg



The final result after correction and finishing, IPA wipedown and no LSP



http://i259.photobucket.com/albums/hh316/nosdrummer91/Scion%20write%20up/DSC_0151.jpg



http://i259.photobucket.com/albums/hh316/nosdrummer91/Scion%20write%20up/DSC_0154.jpg



The final finished hood under all types of lighting



Infratech



http://i259.photobucket.com/albums/hh316/nosdrummer91/Scion%20write%20up/DSC_0160.jpg



Standing halogens



http://i259.photobucket.com/albums/hh316/nosdrummer91/Scion%20write%20up/DSC_0161.jpg



Up close with the halogens



http://i259.photobucket.com/albums/hh316/nosdrummer91/Scion%20write%20up/DSC_0169.jpg



Camera flash only



http://i259.photobucket.com/albums/hh316/nosdrummer91/Scion%20write%20up/DSC_0167.jpg



Finally the Fenix LED



http://i259.photobucket.com/albums/hh316/nosdrummer91/Scion%20write%20up/DSC_0158.jpg



I feel its important to show all kinds of light on the paint to ensure the finish is truly corrected, I know that in the sun that car will be perfect, I dont worry about holograms anymore thanks to the fenix.



Now onto correcting the rest of the car,



I used gloss it 1 step machine polish on the makita with the burgandy megs pad to correct the side of the car as the defects were not as bad as the hood and trunk, I finished the paint with the cyclo again and the evolution polish



After correction with the 1 step machine polish



http://i259.photobucket.com/albums/hh316/nosdrummer91/Scion%20write%20up/DSC_0007.jpg



Rear panels finished out with the evolution polish this time



http://i259.photobucket.com/albums/hh316/nosdrummer91/Scion%20write%20up/DSC_0010.jpg



http://i259.photobucket.com/albums/hh316/nosdrummer91/Scion%20write%20up/DSC_0011.jpg



The trunk was a problem area, lots of coarse swirls, RIDS and long scratches.



http://i259.photobucket.com/albums/hh316/nosdrummer91/Scion%20write%20up/DSC_0086.jpg



http://i259.photobucket.com/albums/hh316/nosdrummer91/Scion%20write%20up/DSC_0084-2.jpg

[dsms]

I wetsanded the deeper scratches with Meguiars 2000grit and then corrected the whole small trunk area using... a cyclo?...YEP!



I used these 4inch blended wool pads and the gloss it extreme cut compound to remove the sadning marks and other defects.



http://i259.photobucket.com/albums/hh316/nosdrummer91/Scion%20write%20up/DSC_0087.jpg



Why the cyclo and not the makita? Well the space I had to work with was very limited being as the trunk area is tiny so two 4inch cyclo wool pads actually fit perfectly for the correction work.



After 3 separate passes with the wool and extreme cut I finished with the cyclo again and the 1 step machine polish on green polishing pads.



After



http://i259.photobucket.com/albums/hh316/nosdrummer91/Scion%20write%20up/DSC_0088.jpg



http://i259.photobucket.com/albums/hh316/nosdrummer91/Scion%20write%20up/DSC_0093.jpg



Fenix shot



http://i259.photobucket.com/albums/hh316/nosdrummer91/Scion%20write%20up/DSC_0090.jpg



I worked my way around the car, polishing the lower bumper and rear license plate areas . Then came the very dreaded drivers side where the high heel damage was done.



After working the rear section with 4inch pads on the makita



http://i259.photobucket.com/albums/hh316/nosdrummer91/Scion%20write%20up/DSC_0141.jpg



Drivers side time, first I spotted some scratches by the drivers side tail light, so out with the sanding paper again :doh:



Before



http://i259.photobucket.com/albums/hh316/nosdrummer91/Scion%20write%20up/DSC_0014.jpg



After sanding with 2000grit and correction with 4inch orange pads on the makita



http://i259.photobucket.com/albums/hh316/nosdrummer91/Scion%20write%20up/DSC_0019.jpg





Onto the most dreaded part of the detail:shakehead:



http://i259.photobucket.com/albums/hh316/nosdrummer91/Scion%20write%20up/DSC_0028.jpg



http://i259.photobucket.com/albums/hh316/nosdrummer91/Scion%20write%20up/DSC_0034.jpg



I saw the extent of the damage now under my lighting, by far the deepest scratches I had dealt with, along with them were coarse swirls and RID`s ( more on these panels than on the rest of the car)



http://i259.photobucket.com/albums/hh316/nosdrummer91/Scion%20write%20up/DSC_0033.jpg



No more games, out with the 1500grit. I sanded the large area of clustered scratches and then spot sanded the random ones





One of the deeper ones



http://i259.photobucket.com/albums/hh316/nosdrummer91/Scion%20write%20up/DSC_0038.jpg



http://i259.photobucket.com/albums/hh316/nosdrummer91/Scion%20write%20up/DSC_0037.jpg



http://i259.photobucket.com/albums/hh316/nosdrummer91/Scion%20write%20up/DSC_0042.jpg



http://i259.photobucket.com/albums/hh316/nosdrummer91/Scion%20write%20up/DSC_0045.jpg



I used a 6inch white lambswool pad for the initial correction (its a double sided pad)



http://i259.photobucket.com/albums/hh316/nosdrummer91/Scion%20write%20up/DSC_0046.jpg



And again I used extreme cut



http://i259.photobucket.com/albums/hh316/nosdrummer91/Scion%20write%20up/DSC_0047.jpg



I used some EVP prime on the wool pad as well so I could polish at higher RPM without generating too much heat, max RPM was about 2400



After the first pass I was pretty pleased to see I got out a good amount of defects but more wetsanding was needed so I hit the deeper scratches again with 1500grit and the finer ones got 2000grit



Again I used the lambswool pad, extreme cut and polished at about 2100rpm for an extended period of time for 2 more passes



The results after compunding with the wool after wetsanding



http://i259.photobucket.com/albums/hh316/nosdrummer91/Scion%20write%20up/DSC_0048.jpg



You can see the heavy hologramming but at least the scratches were taken out, this made me very happy:gidiup:



I began to finish the paint after the compounding with wool, I used the makita and the 1 step machine polish on a meguiars cutting pad, after 2 pass



http://i259.photobucket.com/albums/hh316/nosdrummer91/Scion%20write%20up/DSC_0051.jpg



The top half of that panel also had deep scratches from the high heel, again wetsanded and compunded





http://i259.photobucket.com/albums/hh316/nosdrummer91/Scion%20write%20up/DSC_0061.jpg



After 1 pass with a 4inch blended wool on the makita,



http://i259.photobucket.com/albums/hh316/nosdrummer91/Scion%20write%20up/DSC_0066.jpg



After 2 more passes, 1 with the wool pad and the other with a polishing pad using the 1 step polish to restore the gloss



http://i259.photobucket.com/albums/hh316/nosdrummer91/Scion%20write%20up/DSC_0065.jpg

[dsms]

And after finishing with the cyclo and evolution polish on blue pads, a scratch, swirl and hologram free finish is left



http://i259.photobucket.com/albums/hh316/nosdrummer91/Scion%20write%20up/DSC_0068.jpg



I lined up some bottles to show the clarity in the paint finish after all the correction work was done



http://i259.photobucket.com/albums/hh316/nosdrummer91/Scion%20write%20up/DSC_0069.jpg



The Fenix TK 10 showing the real finish after correction



http://i259.photobucket.com/albums/hh316/nosdrummer91/Scion%20write%20up/DSC_0109-2.jpg



Far from done correcting this Scion however, still have the drivers side door to take care of.



More high heel scratches? No! its like groundhogs day:thud:



http://i259.photobucket.com/albums/hh316/nosdrummer91/Scion%20write%20up/DSC_0073-2.jpg



A pic I took before outside



http://i259.photobucket.com/albums/hh316/nosdrummer91/Scion%20write%20up/DSC_0056.jpg



Just the regular swirls and RIDS on the upper half of the door, guess the heel`s missed this section



http://i259.photobucket.com/albums/hh316/nosdrummer91/Scion%20write%20up/DSC_0074.jpg



Same deal on these scratches, 1500, 200 grit, lambswool pad, foam pad on rotary, finish with cyclo



http://i259.photobucket.com/albums/hh316/nosdrummer91/Scion%20write%20up/DSC_0081-2.jpg



Here is the panel all finished again under the light of truth



http://i259.photobucket.com/albums/hh316/nosdrummer91/Scion%20write%20up/DSC_0110-2.jpg



http://i259.photobucket.com/albums/hh316/nosdrummer91/Scion%20write%20up/DSC_0111.jpg



before, some of those door scratches



http://i259.photobucket.com/albums/hh316/nosdrummer91/Scion%20write%20up/DSC_0076-2.jpg



after



http://i259.photobucket.com/albums/hh316/nosdrummer91/Scion%20write%20up/DSC_0106-2.jpg



Now for the home stretch, no more heel damage just more swirls etc.



http://i259.photobucket.com/albums/hh316/nosdrummer91/Scion%20write%20up/DSC_0098.jpg



http://i259.photobucket.com/albums/hh316/nosdrummer91/Scion%20write%20up/DSC_0102-2.jpg



After 1 step machine polish and finishing with evolution polish



http://i259.photobucket.com/albums/hh316/nosdrummer91/Scion%20write%20up/DSC_0103.jpg



http://i259.photobucket.com/albums/hh316/nosdrummer91/Scion%20write%20up/DSC_0104.jpg



Here is the car post polishing after a quick rinse with just De-Ionized water, followed by an IPA wipedown



http://i259.photobucket.com/albums/hh316/nosdrummer91/Scion%20write%20up/DSC_0105-2.jpg



With all the correction work out of the way I called it quits for day 2, finished up at about 2am and went to sleep.



DAY 3 started with the interior which was in less than stellar shape



http://i259.photobucket.com/albums/hh316/nosdrummer91/Scion%20write%20up/DSC_0121.jpg



http://i259.photobucket.com/albums/hh316/nosdrummer91/Scion%20write%20up/DSC_0122.jpg



http://i259.photobucket.com/albums/hh316/nosdrummer91/Scion%20write%20up/DSC_0120.jpg

[dsms]

After



http://i259.photobucket.com/albums/hh316/nosdrummer91/Scion%20write%20up/DSC_0128.jpg



The trunk wasnt bad, cleaned up the doorjambs with APC 10:1 and a SV brush



http://i259.photobucket.com/albums/hh316/nosdrummer91/Scion%20write%20up/DSC_0117-2.jpg



http://i259.photobucket.com/albums/hh316/nosdrummer91/Scion%20write%20up/DSC_0119.jpg



I really didnt catch a lot of breaks on this one, :giggle:



http://i259.photobucket.com/albums/hh316/nosdrummer91/Scion%20write%20up/DSC_0114-2.jpg



http://i259.photobucket.com/albums/hh316/nosdrummer91/Scion%20write%20up/DSC_0115-2.jpg



http://i259.photobucket.com/albums/hh316/nosdrummer91/Scion%20write%20up/DSC_0116.jpg



the gloss it interior twins worked very well, streaking is a non issue with both of these products I found (dont flame me for this stuff, Im just stating the products I used to get the results i did, if I had a picture of the Lexol twins nobody would bat an eye ...understand where im coming from before I get flamed)



http://i259.photobucket.com/albums/hh316/nosdrummer91/Scion%20write%20up/DSC_0125.jpg





Carpets shampood with Folex, toweled dry and then vacummed



After



http://i259.photobucket.com/albums/hh316/nosdrummer91/Scion%20write%20up/DSC_0132.jpg



http://i259.photobucket.com/albums/hh316/nosdrummer91/Scion%20write%20up/DSC_0133.jpg



Interior process:



-Leather cleaned with gloss it satin leather cleaner

-conditioned with gloss it satin leather polish

-dash treated with gloss it TRV protectant

-plastics cleaned with 1Z cp and Reinger for the stubborn stains



http://i259.photobucket.com/albums/hh316/nosdrummer91/Scion%20write%20up/DSC_0129-2.jpg



As a little touch I like to spray the interior with Febreeze to get that fresh smell into the carpets, I do the same for the trunk compartment



Before going to LSP I performed all the finishing touches:



Glass was cleaned with spray way

Tires dressed with gloss it signature tire gloss

exterior trim treated with 1Z gummi pledge

exhaust polished with NXT megs

wheels sealed with Z-CS



Day 3 ended with the LSP application



Hand application of Gloss It Gloss Finish sealant x1

Hand application of Gloss It Concourso Gloss (great topper for the extra wow)





The concourso gloss on a red CCS before being massaged into the paint



http://i259.photobucket.com/albums/hh316/nosdrummer91/Scion%20write%20up/DSC_0136.jpg



And finally some final shots inside and some outside





http://i259.photobucket.com/albums/hh316/nosdrummer91/Scion%20write%20up/DSC_0143-2.jpg



http://i259.photobucket.com/albums/hh316/nosdrummer91/Scion%20write%20up/DSC_0144.jpg



http://i259.photobucket.com/albums/hh316/nosdrummer91/Scion%20write%20up/DSC_0153.jpg



http://i259.photobucket.com/albums/hh316/nosdrummer91/Scion%20write%20up/DSC_0145.jpg



I had to return the car very early on the 4th day, I caught some shots as the sun came up. My garage shows the depth and clarity very well because the light is shining on every angle. i wish I had some sun to showcase this car but it was only 7am when I took these.



http://i259.photobucket.com/albums/hh316/nosdrummer91/Scion%20write%20up/DSC_0160-2.jpg



http://i259.photobucket.com/albums/hh316/nosdrummer91/Scion%20write%20up/DSC_0158-2.jpg





http://i259.photobucket.com/albums/hh316/nosdrummer91/Scion%20write%20up/DSC_0147-2.jpg



http://i259.photobucket.com/albums/hh316/nosdrummer91/Scion%20write%20up/DSC_0152-2.jpg



http://i259.photobucket.com/albums/hh316/nosdrummer91/Scion%20write%20up/DSC_0157.jpg





Total time... I stopped counting at 25hours on the 3rd day





Well thank you as always for reading, this car was a nice challenge but the end result was worth it. The look on the owners face was hilarious, kind of dumbfounded if you will. Hes thrilled his car looked like it did when it left the showroom and not like it left the junkyard.



Hope you enjoyed





:thumb:[/SIZE]

[Setec Astronomy]

Man, I love your garage, that`s the way I want to do my lighting if I ever get my other garage issues resolved. Nice color on the car, nice work, nice documention/thread!

[Barry Theal]

perfectly well executed detail! good ateention to details good wetsanding, great polish! great compounding! great work. so how do you like them little 4 inchers on rotary? great job !!!! i thought i was the only one that likes those little led!

[DaGonz]

Very nice writeup and work! :bounce :waxing:

[longdx]

Superb writeup and turnaround. I am glad to see a proper review/usage of Gloss-It products. I have a Cyclo and am interested in how these products performed in real world scenarios.

[imported_never gone]

Just an awesome job! You can see the metal flake really popping in the after pics in some spots. Nice work.

[imported_d00t]

David, jesus! I think this is up there with your best yet. Love the work! I think Bob influenced us all with that light.. I don`t go anywhere without it ;). How do you like the camspray? I`m having troubles justifying the $700 price tag..



Again, amazing work. You`ve really figured out how to work the gloss-it stuff. I`m still learning it, and practicing often, but can`t quite get it down like you can. I`m very impressed!



Aaron

[rwisejr]

I hope he got rid of that girlfriend or the car will be back to where it was .Great work !!!!!!!!!!

[Apollo_Auto]

Nice save buddy! I enjoyed that one!

[imported_smprince1]

Great write up and excellent work. Results look great :2thumbs:

[Thomas Dekany]

This may be your best write up yet.



Beautiful result!!!!:bow:bow:bow