Me, The PC, Or Poorboys...Help!

[imported_tonymontana]

Ok....so I set out today to use my PC for the first time along with Poorboys 2.5. I was able to wash the car and clay no problem......after that, it was a different story!



I started with a yellow propel pad, PB 2.5, and the pc. I started with 4 dime size squirts and turned on the pc at dial set to 2. After a few passes I bumped it up to 5. I started on the bumper of my black G35 and after doing the vertical, horizontal, and the diagonal passes, I paused to check. I noticed some hazing that would not go away in addition to the swirls and scratches that I thought would be gone after using PB 2.5.



I double checked the pad chart to see if I used the wrong pad....so I referred to this thread:

http://www.detailcity.com/forums/showthread.php?t=14489



I thought maybe I should switch to a polishing pad....blue propel it was. That did not help either (I figured it wouldn`t but I was desperate).



Anyway after 6.5 hours with only one pass of PBs 2.5 with a yellow pad, and one pass with PBs 2.5 on a blue propel....I found the car to be shiny but no luck with the swirl removal or scratches on the car.....more importantly, I could not get rid of some the hazing.....could it be due to not keeping the pad flat while making passes on the curves of the car? did I burn the paint?



Any advice from on how to remove the hazing? At this point I am not as concerned about the swirl marks but wish they were gone....kinda disappointed with PBs but I know its something I am doing wrong.



Trying to use:



1. PBs 2.5

2. VMG

3. EX

4. Nattys blue



Using available propel pads 6" yellow, blue, green, black and 4" yellow, blue, green with a pc



Initial dirty car with swirls

http://home.earthlink.net/~kobeshin1/initial%20g35.JPG



Started by working product in at 2 and then bumped speed to 5- I think I used too much product and I did NOT mist the pad

http://home.earthlink.net/~kobeshin1/firstpassG35.JPG



Got most of the product out...you can see reflection of electric cord with hazing in the middle of the door.

http://home.earthlink.net/~kobeshin1/HazeafterG35.JPG



Thanks for your advice everyone.....

[imported_chpsk8]

Those are some pretty small pics, so it might be hard to tell. Did the polish ever get opaque while you were working it?

The onle pic with the polish on it almost looks like there was too much product on the pad. Was the pad seasoned well before it hit the paint? (seasoned meaning "loaded")

[Setec Astronomy]

It`s a little hard to see from the picture, but I would say you need to break down the polish a little more to get rid of the hazing. On black, I`m not sure you won`t get some hazing anyway and have to follow it with a finer polish, and I`m not sure if VM has enough bite to remove the SSR2.5 hazing. Someone else with a little more experience with these will have to chime in.

[imported_tonymontana]

I will have to upload bigger pics when I get home tonite...but the PBs 2.5 hazed and even after rubbing it with a MF towel.....



I have in my collection:



AIO

RNG

VM

PB 1, 2, 2.5

Nattys blue



Optimum spray wax, and megs QD



Will an agressive polish clean up the haze? Has anyone experienced this before where they see hazing and use another product to clean it up and get a clean surface? Is this normal?



Thanks for your time....

[imported_chpsk8]

A less aggressive polish would be the next move. Always use the least agressive that will do the job. I think you may have used too aggressive of a compound.

Never fear though, it can be repaired. Try some PB1 in a small spot. Work it until it turns opaque and breaks down. That should cure your ill.

If PB1 doesn`t cut it, then go a little more aggressive.



In the future, start with the least agressive to fix the problem.

[SpoiledMan]

I will have to upload bigger pics when I get home tonite...but the PBs 2.5 hazed and even after rubbing it with a MF towel.....



I have in my collection:



AIO

RNG

VM

PB 1, 2, 2.5

Nattys blue



Optimum spray wax, and megs QD



Will an agressive polish clean up the haze? Has anyone experienced this before where they see hazing and use another product to clean it up and get a clean surface? Is this normal?



Thanks for your time....



If you can`t get it to work please PM me. I just might come to your house and MAKE it work.:)

[TGates]

It would have been BETTER to try SSR1 first, but 2.5, when worked long enough, breaks down almost as well as SSR1. I don`t think you damaged your paint. My G35 did the exact same thing after using Zaino, and the polishes I tried never got rid of the hazing completely. Don`t be afraid to crank the PC up to 6 when polishing. Use a polishing pad, prime it, and work the 2.5 until it starts to dust, then wipe what`s remaining off with a MF.

[ceiol]

use less product, finer pad, higher speed, move slower, let the 2.5 break down fully

[adept]

use less product, finer pad, higher speed, move slower, let the 2.5 break down fully



exactly what he said

[aaron33]

I also use the yellow Propel with SSR2.5. Do you remember if the SSR2.5 dried up while you were working with it? I find that I have to give a spray of water onto the pad to keep it moist and not end up with dry SSR2.5 with the yellow pad which would definitely cause hazing.



Now that the hazing part is gone, I found that with the PC and SSR2.5, it does not remove swirls that quickly. I usually spread the product at low speed and then do a 4 pass consisting of vertical, horizontal, diagonal, vertical, horizontal, diagonal and finally back to vertical, while applying sufficient pressure. Really, the PC, yellow propel and SSR2.5 is still a very mild combo compared to a rotary. I even find with the 7 passes, I still have to move the PC slowly with enough pressure. After that, I follow up with SSR1 with a blue propel.

[imported_tonymontana]

I think I made the following mistakes:



1. DId not mist the propel yellow cutting pad or the blue propel polishing pad



2. Used too much product (PB 2.5) 4 dime size squirts on the outer part of the pads equally spaced



3. Went to 2.5 when I should have tried 1.0 or 2.0 first.



I thought I worked the product in for a good amount of time doing all the passes but realized if I used to much product.....it probably would have never broken down.



I was not able to remove swirl or scratch marks...is this something I wont see with 2.5 or should I be more agreesive with the pc?



Thanks for you help....

[blkyukon]

Like everyone else said, from the pics it looks like you might have used too much product and didn`t break it down enough.





Here is the amount of SSR2.5 I used and what it looks likes when it`s broken down:



http://melncal.com/detailing/polish/images/02.jpg



http://melncal.com/detailing/polish/images/08.jpg



Here are the stages they go through:



http://users.ca.astound.net/blkyukon/cars/ssr.html





Below shows what one pass with a medium aggressive polish like DACP or SSR2.5 can remove.



It doesn`t remove everything but did remove the majority of imperfections.

http://img.photobucket.com/albums/v213/blkyukon/dacp_fp_before.jpg

http://img.photobucket.com/albums/v213/blkyukon/dacp_fp_after.jpg

[aaron33]

I think I made the following mistakes:



1. DId not mist the propel yellow cutting pad or the blue propel polishing pad



2. Used too much product (PB 2.5) 4 dime size squirts on the outer part of the pads equally spaced



3. Went to 2.5 when I should have tried 1.0 or 2.0 first.



I thought I worked the product in for a good amount of time doing all the passes but realized if I used to much product.....it probably would have never broken down.



I was not able to remove swirl or scratch marks...is this something I wont see with 2.5 or should I be more agreesive with the pc?



Thanks for you help....

Yeah, try less product like what blkyukon showed. SSR1 is more of a finishing polish. Don`t expect it to take out anything other than hazing.



Less is better. Once it has broken down, you just wipe off and then repeat another series of passes with more product if you see that the swirls are still there. Many repeats with just enough product is much better than 1 series of passes with a lot of product.

[ceiol]

Like everyone else said, from the pics it looks like you might have used too much product and didn`t break it down enough.





Here is the amount of SSR2.5 I used and what it looks likes when it`s broken down:



http://img.photobucket.com/albums/v213/blkyukon/polish/update/02.jpg



http://img.photobucket.com/albums/v213/blkyukon/polish/update/08.jpg



Here are the stages they go through:



http://users.ca.astound.net/blkyukon/cars/ssr.html





Below shows what one pass with a medium aggressive polish like DACP or SSR2.5 can remove.



It doesn`t remove everything but did remove the majority of imperfections.

http://img.photobucket.com/albums/v213/blkyukon/dacp_fp_before.jpg

http://img.photobucket.com/albums/v213/blkyukon/dacp_fp_after.jpg



great pics -- amazing that you keep that black yukon looking so good.

[Sherman8r44]

I think I made the following mistakes:

1. DId not mist the propel yellow cutting pad or the blue propel polishing pad



Steve (the owner of Poorboy`s) says to NOT mist the pads when using PB polishes.